search..
No manual entry for -- in section 8
IP-LINK(8)			     Linux			     IP-LINK(8)

NAME
       ip-link - network device configuration

SYNOPSIS
       ip link	{ COMMAND | help }

       ip link add [ link DEVICE ] [ name ] NAME
	       [ txqueuelen PACKETS ]
	       [ address LLADDR ] [ broadcast LLADDR ]
	       [ mtu MTU ] [ index IDX ]
	       [ numtxqueues QUEUE_COUNT ] [ numrxqueues QUEUE_COUNT ]
	       [ gso_max_size BYTES ] [ gso_ipv4_max_size BYTES ] [
	       gso_max_segs SEGMENTS ]
	       [ gro_max_size BYTES ] [ gro_ipv4_max_size BYTES ]
	       [ netns { PID | NETNSNAME | NETNSFILE } ]
	       type TYPE [ ARGS ]

       ip link delete { DEVICE | group GROUP } type TYPE [ ARGS ]

       ip link { set | change } { DEVICE | group GROUP }
	       [ { up | down } ]
	       [ type ETYPE TYPE_ARGS ]
	       [ arp { on | off } ]
	       [ dynamic { on | off } ]
	       [ multicast { on | off } ]
	       [ allmulticast { on | off } ]
	       [ promisc { on | off } ]
	       [ protodown { on | off } ]
	       [ protodown_reason PREASON { on | off } ]
	       [ trailers { on | off } ]
	       [ txqueuelen PACKETS ]
	       [ gso_max_size BYTES ] [ gso_ipv4_max_size BYTES ] [
	       gso_max_segs SEGMENTS ]
	       [ gro_max_size BYTES ] [ gro_ipv4_max_size BYTES ]
	       [ name NEWNAME ]
	       [ address LLADDR ]
	       [ broadcast LLADDR ]
	       [ mtu MTU ]
	       [ netns { PID | NETNSNAME | NETNSFILE } ]
	       [ link-netnsid ID ]
	       [ alias NAME ]
	       [ vf NUM [ mac LLADDR ]
			[ VFVLAN-LIST ]
			[ rate TXRATE ]
			[ max_tx_rate TXRATE ]
			[ min_tx_rate TXRATE ]
			[ spoofchk { on | off } ]
			[ query_rss { on | off } ]
			[ state { auto | enable | disable } ]
			[ trust { on | off } ]
			[ node_guid eui64 ]
			[ port_guid eui64 ] ]
	       [ { xdp | xdpgeneric | xdpdrv | xdpoffload } { off |
		       object FILE [ { section | program } NAME ] [ verbose ] |
		       pinned FILE } ]
	       [ master DEVICE ]
	       [ nomaster ]
	       [ vrf NAME ]
	       [ addrgenmode { eui64 | none | stable_secret | random } ]
	       [ macaddr [ MACADDR ]
			 [ { flush | add | del } MACADDR ]
			 [ set MACADDR ] ]

		 ip link show [ DEVICE | group GROUP ] [ { up | down } ] [ mas-
			 ter DEVICE ] [ type ETYPE ] [ vrf NAME ] [ nomaster ]
			 [ novf ]

		 ip link xstats type TYPE [ ARGS ]

		 ip link afstats [ dev DEVICE ]

		 ip link help [ TYPE ]

		 TYPE := [ amt | bareudp | bond | bridge | can | dsa | dummy |
			 erspan | geneve | gre | gretap | gtp | hsr | ifb |
			 ip6erspan | ip6gre | ip6gretap | ip6tnl | ipip | ipoib
			 | ipvlan | ipvtap | lowpan | macsec | macvlan | macv-
			 tap | netdevsim | netkit | nlmon | pfcp | rmnet | sit
			 | vcan | veth | virt_wifi | vlan | vrf | vti | vxcan |
			 vxlan | xfrm ]

		 ETYPE := [ TYPE | bridge_slave | bond_slave ]

		 VFVLAN-LIST := [ VFVLAN-LIST ] VFVLAN

		 VFVLAN := [ vlan VLANID [ qos VLAN-QOS ] [ proto VLAN-PROTO ]
			 ]

	 ip link property add dev DEVICE [ altname NAME .. ]

	 ip link property del dev DEVICE [ altname NAME .. ]

DESCRIPTION
   ip link add - add virtual link
       link DEVICE
	      specifies the physical device to act operate on.

	      NAME specifies the name of the new virtual device.

	      TYPE specifies the type of the new device.

	      Link types:

		      amt - Automatic Multicast Tunneling (AMT)

		      bareudp - Bare UDP L3 encapsulation support

		      bond - Bonding device

		      bridge - Ethernet Bridge device

		      can - Controller Area Network

		      dsa - Distributed Switch Architecture

		      dummy - Dummy network interface

		      erspan - Encapsulated Remote SPAN over GRE and IPv4

		      geneve - GEneric NEtwork Virtualization Encapsulation

		      gre - Virtual tunnel interface GRE over IPv4

		      gretap - Virtual L2 tunnel interface GRE over IPv4

		      gtp - GPRS Tunneling Protocol

		      hsr - High-availability Seamless Redundancy device

		      ifb - Intermediate Functional Block device

		      ip6erspan - Encapsulated Remote SPAN over GRE and IPv6

		      ip6gre - Virtual tunnel interface GRE over IPv6

		      ip6gretap - Virtual L2 tunnel interface GRE over IPv6

		      ip6tnl - Virtual tunnel interface IPv4|IPv6 over IPv6

		      ipip - Virtual tunnel interface IPv4 over IPv4

		      ipoib - IP over Infiniband device

		      ipvlan - Interface for L3 (IPv6/IPv4) based VLANs

		      ipvtap - Interface for L3 (IPv6/IPv4) based VLANs and TAP

		      lowpan  - Interface for 6LoWPAN (IPv6) over IEEE 802.15.4
		      / Bluetooth

		      macsec - Interface for IEEE 802.1AE MAC Security (MACsec)

		      macvlan - Virtual interface base on  link	 layer	address
		      (MAC)

		      macvtap  -  Virtual interface based on link layer address
		      (MAC) and TAP.

		      netdevsim - Interface for netdev API tests

		      netkit - BPF-programmable network device

		      nlmon - Netlink monitoring device

		      pfcp - Packet Forwarding Control Protocol device

		      rmnet - Qualcomm rmnet device

		      sit - Virtual tunnel interface IPv6 over IPv4

		      vcan - Virtual Controller Area Network interface

		      veth - Virtual ethernet interface

		      virt_wifi - rtnetlink wifi simulation device

		      vlan - 802.1q tagged virtual LAN interface

		      vrf - Interface for L3 VRF domains

		      vti - Virtual tunnel interface

		      vxcan - Virtual Controller Area Network tunnel interface

		      vxlan - Virtual eXtended LAN

		      xfrm - Virtual xfrm interface

       numtxqueues QUEUE_COUNT
	      specifies the number of transmit queues for new device.

       numrxqueues QUEUE_COUNT
	      specifies the number of receive queues for new device.

       gso_max_size BYTES
	      specifies the recommended maximum size of a Generic  Segment  Of-
	      fload  packet  the new device should accept. This is also used to
	      enable BIG TCP for IPv6 on this device when the size  is	greater
	      than 65536.

       gso_ipv4_max_size BYTES
	      specifies	 the recommended maximum size of a IPv4 Generic Segment
	      Offload packet the new device should accept. This	 is  especially
	      used  to	enable	BIG TCP for IPv4 on this device by setting to a
	      size greater than 65536.	Note that gso_max_size needs to be  set
	      to  a  size  greater than or equal to gso_ipv4_max_size to really
	      enable BIG TCP for IPv4.

       gso_max_segs SEGMENTS
	      specifies the recommended maximum number of a Generic Segment Of-
	      fload segments the new device should accept.

       gro_max_size BYTES
	      specifies the maximum size of a packet built by GRO stack on this
	      device. This is also used for BIG TCP to	allow  the  size  of  a
	      merged IPv6 GSO packet on this device greater than 65536.

       gro_ipv4_max_size BYTES
	      specifies the maximum size of a IPv4 packet built by GRO stack on
	      this  device.  This  is  especially used for BIG TCP to allow the
	      size of a merged IPv4 GSO packet	on  this  device  greater  than
	      65536.

       index IDX
	      specifies	 the  desired index of the new virtual device. The link
	      creation fails, if the index is busy.

       netns  { PID | NETNSNAME | NETNSFILE }
	      create the  device  in  the  network  namespace  associated  with
	      process PID or the name NETNSNAME or the file NETNSFILE.

       VLAN Type Support
	      For  a  link  of type VLAN the following additional arguments are
	      supported:

	      ip link add link DEVICE name NAME type vlan [ protocol VLAN_PROTO
	      ] id VLANID [ reorder_hdr { on | off } ] [ gvrp { on | off } ]  [
	      mvrp { on | off } ] [ loose_binding { on | off } ] [ bridge_bind-
	      ing  {  on | off } ] [ ingress-qos-map QOS-MAP ] [ egress-qos-map
	      QOS-MAP ]

		      protocol VLAN_PROTO - either 802.1Q or 802.1ad.

		      id VLANID - specifies the VLAN Identifier	 to  use.  Note
		      that  numbers  with  a leading " 0 " or " 0x " are inter-
		      preted as octal or hexadecimal, respectively.

		      reorder_hdr { on | off }	-  specifies  whether  ethernet
		      headers are reordered or not (default is on).

			  If reorder_hdr is on then VLAN header will be not in-
			  serted  immediately  but  only  before passing to the
			  physical device (if this device does not support VLAN
			  offloading), the similar on the RX direction - by de-
			  fault the packet will be untagged  before  being  re-
			  ceived  by  VLAN device. Reordering allows one to ac-
			  celerate tagging on egress and to hide VLAN header on
			  ingress so the packet	 looks	like  regular  Ethernet
			  packet,  at  the  same time it might be confusing for
			  packet capture as the	 VLAN  header  does  not  exist
			  within the packet.

			  VLAN offloading can be checked by ethtool(8):

			      ethtool -k <phy_dev> | grep tx-vlan-offload

			  where	 <phy_dev> is the physical device to which VLAN
			  device is bound.

		      gvrp { on | off } - specifies whether this VLAN should be
		      registered using GARP VLAN Registration Protocol.

		      mvrp { on | off } - specifies whether this VLAN should be
		      registered using Multiple VLAN Registration Protocol.

		      loose_binding { on | off } - specifies whether  the  VLAN
		      device state is bound to the physical device state.

		      bridge_binding  { on | off } - specifies whether the VLAN
		      device link state tracks the state of bridge  ports  that
		      are members of the VLAN.

		      ingress-qos-map  QOS-MAP	-  defines  a  mapping	of VLAN
		      header prio field to the Linux internal  packet  priority
		      on  incoming  frames. The format is FROM:TO with multiple
		      mappings separated by spaces.

		      egress-qos-map QOS-MAP - defines a mapping of  Linux  in-
		      ternal  packet priority to VLAN header prio field but for
		      outgoing frames. The format is the same as  for  ingress-
		      qos-map.

			  Linux packet priority can be set by iptables(8):

			      iptables	-t mangle -A POSTROUTING [...] -j CLAS-
			      SIFY --set-class 0:4

			  and this "4" priority can be used in the  egress  qos
			  mapping to set VLAN prio "5":

			      ip link set veth0.10 type vlan egress 4:5

       VXLAN Type Support
	      For  a  link of type VXLAN the following additional arguments are
	      supported:

	      ip link add DEVICE type vxlan id VNI [ dev PHYS_DEV  ] [ {  group
	      |	 remote } IPADDR ] [ local { IPADDR | any } ] [ ttl TTL ] [ tos
	      TOS ] [ df DF ] [ flowlabel FLOWLABEL ] [ dstport PORT ]	[  src-
	      port  MIN	 MAX  ]	 [  reserved_bits  VALUE  ]  [ [no]learning ] [
	      [no]proxy ] [ [no]rsc ] [ [no]l2miss ] [ [no]l3miss ] [ [no]udpc-
	      sum ] [ [no]udp6zerocsumtx ] [ [no]udp6zerocsumrx ] [  [no]local-
	      bypass  ] [ ageing SECONDS ] [ maxaddress NUMBER ] [ [no]external
	      ] [ gbp ] [ gpe ] [ [no]vnifilter ]

		      id VNI - specifies the VXLAN Network Identifier (or VXLAN
		      Segment Identifier) to use.

		      dev PHYS_DEV - specifies the physical device to  use  for
		      tunnel endpoint communication.

		      group  IPADDR  -	specifies  the	multicast IP address to
		      join.  This parameter cannot be specified with the remote
		      parameter.

		      remote IPADDR - specifies the unicast destination IP  ad-
		      dress  to	 use  in  outgoing packets when the destination
		      link layer address is not known in the VXLAN device  for-
		      warding database. This parameter cannot be specified with
		      the group parameter.

		      local  IPADDR - specifies the source IP address to use in
		      outgoing packets.

		      ttl TTL - specifies the TTL  value  to  use  in  outgoing
		      packets.

		      tos  TOS	-  specifies  the  TOS value to use in outgoing
		      packets.

		      df DF - specifies the usage of the  Don't	 Fragment  flag
		      (DF) bit in outgoing packets with IPv4 headers. The value
		      inherit  causes the bit to be copied from the original IP
		      header. The values unset and set cause the bit to be  al-
		      ways  unset  or always set, respectively. By default, the
		      bit is not set.

		      flowlabel FLOWLABEL - specifies the flow label to use  in
		      outgoing packets.

		      dstport PORT - specifies the UDP destination port to com-
		      municate to the remote
			VXLAN tunnel endpoint.

		      srcport  MIN MAX - specifies the range of port numbers to
		      use as UDP source ports  to  communicate	to  the	 remote
		      VXLAN tunnel endpoint.

		      reserved_bits VALUE - by default the kernel rejects pack-
		      ets  that have bits set outside of the fields required by
		      the  features  enabled  on  the  VXLAN   netdevice.   re-
		      served_bits is a 64-bit quantity specifying which bits it
		      should be possible to set in a VXLAN header. Each bit set
		      in the value is a tolerated bit set in a packet.

		      [no]learning - specifies if unknown source link layer ad-
		      dresses  and  IP addresses are entered into the VXLAN de-
		      vice forwarding database.

		      [no]rsc - specifies if route short circuit is turned on.

		      [no]proxy - specifies ARP proxy is turned on.

		      [no]l2miss - specifies if netlink LLADDR	miss  notifica-
		      tions are generated.

		      [no]l3miss  - specifies if netlink IP ADDR miss notifica-
		      tions are generated.

		      [no]udpcsum - specifies if UDP checksum is calculated for
		      transmitted packets over IPv4.

		      [no]udp6zerocsumtx - skip UDP  checksum  calculation  for
		      transmitted packets over IPv6.

		      [no]udp6zerocsumrx - allow incoming UDP packets over IPv6
		      with zero checksum field.

		      [no]localbypass - if FDB destination is local, with nolo-
		      calbypass	 set, forward encapsulated packets to the user-
		      space network stack. If there is a userspace process lis-
		      tening for these	packets,  it  will  have  a  chance  to
		      process  them. If localbypass is active (default), bypass
		      the kernel network stack and inject the packets into  the
		      target VXLAN device, assuming one exists.

		      ageing SECONDS - specifies the lifetime in seconds of FDB
		      entries learnt by the kernel.

		      maxaddress  NUMBER  - specifies the maximum number of FDB
		      entries.

		      [no]external -  specifies	 whether  an  external	control
		      plane (e.g. ip route encap) or the internal FDB should be
		      used.

		      [no]vnifilter - specifies whether the vxlan device is ca-
		      pable  of	 vni  filtering. Only works with a vxlan device
		      with external flag set. once enabled, bridge vni	command
		      is  used to manage the vni filtering table on the device.
		      The device can only receive packets with vni's configured
		      in the vni filtering table.

		      gbp - enables the Group Policy extension (VXLAN-GBP).

			  Allows one to transport group policy	context	 across
			  VXLAN	 network  peers.  If enabled, includes the mark
			  of a packet in the VXLAN header for outgoing	packets
			  and  fills  the  packet mark based on the information
			  found in the VXLAN header for incoming packets.

			  Format of upper 16 bits of packet mark (flags);

			    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
			    |-|-|-|-|-|-|-|-|-|D|-|-|A|-|-|-|
			    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

			    D := Don't Learn bit. When set, this bit  indicates
			    that  the egress VTEP MUST NOT learn the source ad-
			    dress of the encapsulated frame.

			    A := Indicates that the group  policy  has	already
			    been  applied  to this packet. Policies MUST NOT be
			    applied by devices when the A bit is set.

			  Format of lower 16 bits of packet mark (policy ID):

			    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
			    |	     Group Policy ID	    |
			    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

			  Example:
			    iptables -A OUTPUT [...] -j MARK --set-mark 0x800FF

		      gpe - enables the Generic Protocol extension (VXLAN-GPE).
		      Currently, this is only supported together with  the  ex-
		      ternal keyword.

       VETH, VXCAN Type Support
	      For a link of types VETH/VXCAN the following additional arguments
	      are supported:

	      ip link add DEVICE type { veth | vxcan } [ peer name NAME ]

		      peer  name  NAME - specifies the virtual pair device name
		      of the VETH/VXCAN tunnel.

       netkit Type Support
	      For a link of type netkit the following additional arguments  are
	      supported:

	      ip  link	add  DEVICE type netkit [ mode MODE ] [ scrub SCRUB ] [
	      POLICY ] [ peer [ scrub SCRUB ] [ POLICY ] [ NAME ] ]

		      mode MODE - specifies the operation mode	of  the	 netkit
		      device with "l3" and "l2" as possible values. Default op-
		      tion is "l3".

		      scrub  SCRUB - specifies the scrub behavior of the netkit
		      device with "default" and "none" as possible values. With
		      "default"	 the  device  zeroes  the  skb->{mark,priority}
		      fields  before invoking the attached BPF program when its
		      peer device resides in  a	 different  network  namespace.
		      With  "none" the device leaves clearing skb->{mark,prior-
		      ity} up to the BPF program. Default option is  "default".
		      Specifying  scrub	 before	 the  peer option refers to the
		      primary device, after the peer option refers to the  peer
		      device.

		      POLICY  - specifies the default device policy when no BPF
		      programs are attached with "forward" and	"blackhole"  as
		      possible	values. Default option is "forward". Specifying
		      policy before the peer option refers to the  primary  de-
		      vice, after the peer option refers to the peer device.

		      NAME - specifies the device name of the peer device.

       IPIP, SIT Type Support
	      For  a  link of type IPIPorSIT the following additional arguments
	      are supported:

	      ip link add DEVICE type { ipip | sit }  remote ADDR local ADDR  [
	      encap  {	fou  | gue | none } ] [ encap-sport { PORT | auto } ] [
	      encap-dport PORT ] [ [no]encap-csum ] [  [no]encap-remcsum ]  [
	      mode  { ip6ip | ipip | mplsip | any } ] [ external ]

		      remote ADDR - specifies the remote address of the tunnel.

		      local  ADDR  - specifies the fixed local address for tun-
		      neled packets.  It must be an address on	another	 inter-
		      face on this host.

		      encap  { fou | gue | none } - specifies type of secondary
		      UDP encapsulation. "fou"	indicates  Foo-Over-UDP,  "gue"
		      indicates Generic UDP Encapsulation.

		      encap-sport  {  PORT | auto } - specifies the source port
		      in UDP encapsulation.  PORT indicates the port by number,
		      "auto" indicates that the port number  should  be	 chosen
		      automatically  (the kernel picks a flow based on the flow
		      hash of the encapsulated packet).

		      [no]encap-csum - specifies if UDP checksums  are	enabled
		      in the secondary encapsulation.

		      [no]encap-remcsum	 - specifies if Remote Checksum Offload
		      is enabled. This is only applicable for Generic  UDP  En-
		      capsulation.

		      mode  { ip6ip | ipip | mplsip | any } - specifies mode in
		      which device should  run.	 "ip6ip"  indicates  IPv6-Over-
		      IPv4,  "ipip"  indicates "IPv4-Over-IPv4", "mplsip" indi-
		      cates MPLS-Over-IPv4, "any" indicates IPv6, IPv4 or  MPLS
		      Over IPv4. Supported for SIT where the default is "ip6ip"
		      and  IPIP where the default is "ipip".  IPv6-Over-IPv4 is
		      not supported for IPIP.

		      external - make this tunnel externally  controlled  (e.g.
		      ip route encap).

       GRE Type Support
	      For  a  link of type GRE or GRETAP the following additional argu-
	      ments are supported:

	      ip link add DEVICE type { gre | gretap }	remote ADDR local  ADDR
	      [	 [no][i|o]seq ] [ [i|o]key KEY | no[i|o]key ] [ [no][i|o]csum ]
	      [ ttl TTL ] [ tos TOS ] [ [no]pmtudisc ] [ [no]ignore-df ] [  dev
	      PHYS_DEV	] [ encap { fou | gue | none } ] [ encap-sport { PORT |
	      auto } ] [ encap-dport PORT ] [ [no]encap-csum ] [ [no]encap-rem-
	      csum ] [ external ]

		      remote ADDR - specifies the remote address of the tunnel.

		      local ADDR - specifies the fixed local address  for  tun-
		      neled  packets.	It must be an address on another inter-
		      face on this host.

		      [no][i|o]seq - serialize packets.	 The oseq flag	enables
		      sequencing  of  outgoing packets.	 The iseq flag requires
		      that all input packets are serialized.

		      [i|o]key KEY | no[i|o]key - use keyed GRE with  key  KEY.
		      KEY  is  either  a  number or an IPv4 address-like dotted
		      quad.  The key parameter specifies the same key to use in
		      both directions.	The ikey and  okey  parameters	specify
		      different keys for input and output.

		      [no][i|o]csum  -	generate/require checksums for tunneled
		      packets.	The ocsum flag calculates checksums for	 outgo-
		      ing  packets.   The  icsum  flag	requires that all input
		      packets have the	correct	 checksum.  The	 csum  flag  is
		      equivalent to the combination icsum ocsum .

		      ttl  TTL	-  specifies  the  TTL value to use in outgoing
		      packets.

		      tos TOS - specifies the TOS  value  to  use  in  outgoing
		      packets.

		      [no]pmtudisc  -  enables/disables	 Path  MTU Discovery on
		      this tunnel.  It is enabled by default. Note that a fixed
		      ttl is incompatible with this option:  tunneling	with  a
		      fixed ttl always makes pmtu discovery.

		      [no]ignore-df  -	enables/disables IPv4 DF suppression on
		      this tunnel.  Normally datagrams that exceed the MTU will
		      be fragmented; the presence of the DF flag inhibits this,
		      resulting instead in an ICMP  Unreachable	 (Fragmentation
		      Required) message.  Enabling this attribute causes the DF
		      flag to be ignored.

		      dev  PHYS_DEV  - specifies the physical device to use for
		      tunnel endpoint communication.

		      encap { fou | gue | none } - specifies type of  secondary
		      UDP  encapsulation.  "fou"  indicates Foo-Over-UDP, "gue"
		      indicates Generic UDP Encapsulation.

		      encap-sport { PORT | auto } - specifies the  source  port
		      in UDP encapsulation.  PORT indicates the port by number,
		      "auto"  indicates	 that  the port number should be chosen
		      automatically (the kernel picks a flow based on the  flow
		      hash of the encapsulated packet).

		      [no]encap-csum  -	 specifies if UDP checksums are enabled
		      in the secondary encapsulation.

		      [no]encap-remcsum - specifies if Remote Checksum	Offload
		      is  enabled.  This is only applicable for Generic UDP En-
		      capsulation.

		      external - make this tunnel externally  controlled  (e.g.
		      ip route encap).

       IP6GRE/IP6GRETAP Type Support
	      For  a link of type IP6GRE/IP6GRETAP the following additional ar-
	      guments are supported:

	      ip link add DEVICE type { ip6gre | ip6gretap } remote ADDR  local
	      ADDR   [	 [no][i|o]seq  ]  [  [i|o]key  KEY  |  no[i|o]key  ]  [
	      [no][i|o]csum ] [ hoplimit TTL ] [ encaplimit  ELIM  ]  [	 tclass
	      TCLASS ] [ flowlabel FLOWLABEL ] [ dscp inherit ] [ [no]allow-lo-
	      calremote ] [ dev PHYS_DEV ] [ external ]

		      remote  ADDR  -  specifies the remote IPv6 address of the
		      tunnel.

		      local ADDR - specifies the fixed local IPv6  address  for
		      tunneled	packets.   It must be an address on another in-
		      terface on this host.

		      [no][i|o]seq - serialize packets.	 The oseq flag	enables
		      sequencing  of  outgoing packets.	 The iseq flag requires
		      that all input packets are serialized.

		      [i|o]key KEY | no[i|o]key - use keyed GRE with  key  KEY.
		      KEY  is  either  a  number or an IPv4 address-like dotted
		      quad.  The key parameter specifies the same key to use in
		      both directions.	The ikey and  okey  parameters	specify
		      different keys for input and output.

		      [no][i|o]csum  -	generate/require checksums for tunneled
		      packets.	The ocsum flag calculates checksums for	 outgo-
		      ing  packets.   The  icsum  flag	requires that all input
		      packets have the	correct	 checksum.  The	 csum  flag  is
		      equivalent to the combination icsum ocsum.

		      hoplimit TTL - specifies Hop Limit value to use in outgo-
		      ing packets.

		      encaplimit  ELIM - specifies a fixed encapsulation limit.
		      Default is 4.

		      flowlabel FLOWLABEL - specifies a fixed flowlabel.

		      [no]allow-localremote - specifies whether to allow remote
		      endpoint to have an address configured on local host.

		      tclass TCLASS - specifies the traffic class field on tun-
		      neled packets, which can be specified as	either	a  two-
		      digit  hex  value	 (e.g. c0) or a predefined string (e.g.
		      internet).  The value inherit  causes  the  field	 to  be
		      copied  from  the	 original  IP  header.	The  values in-
		      herit/STRING or inherit/00..ff  will  set	 the  field  to
		      STRING  or  00..ff when tunneling non-IP packets. The de-
		      fault value is 00.

		      external - make this  tunnel  externally	controlled  (or
		      not,  which  is the default).  In the kernel, this is re-
		      ferred to as collect metadata mode.  This flag  is  mutu-
		      ally  exclusive  with  the remote, local, seq, key, csum,
		      hoplimit, encaplimit, flowlabel and tclass options.

       IPoIB Type Support
	      For a link of type IPoIB the following additional	 arguments  are
	      supported:

	      ip link add DEVICE name NAME type ipoib [ pkey PKEY ] [ mode MODE
	      ]

		      pkey PKEY - specifies the IB P-Key to use.

		      mode MODE - specifies the mode (datagram or connected) to
		      use.

       ERSPAN Type Support
	      For  a link of type ERSPAN/IP6ERSPAN the following additional ar-
	      guments are supported:

	      ip link add DEVICE type { erspan | ip6erspan } remote ADDR  local
	      ADDR seq key KEY erspan_ver version [ erspan IDX ] [ erspan_dir {
	      ingress | egress } ] [ erspan_hwid hwid ] [ [no]allow-localremote
	      ] [ external ]

		      remote ADDR - specifies the remote address of the tunnel.

		      local  ADDR  - specifies the fixed local address for tun-
		      neled packets.  It must be an address on	another	 inter-
		      face on this host.

		      erspan_ver version - specifies the ERSPAN version number.
		      version indicates the ERSPAN version to be created: 0 for
		      version 0 type I, 1 for version 1 (type II) or 2 for ver-
		      sion 2 (type III).

		      erspan  IDX  -  specifies the ERSPAN v1 index field.  IDX
		      indicates a 20 bit index/port number associated with  the
		      ERSPAN traffic's source port and direction.

		      erspan_dir { ingress | egress } - specifies the ERSPAN v2
		      mirrored traffic's direction.

		      erspan_hwid  hwid	 - an unique identifier of an ERSPAN v2
		      engine within a system.  hwid is a 6-bit value for  users
		      to configure.

		      [no]allow-localremote - specifies whether to allow remote
		      endpoint to have an address configured on local host.

		      external	-  make	 this  tunnel externally controlled (or
		      not, which is the default).  In the kernel, this	is  re-
		      ferred  to  as collect metadata mode.  This flag is mutu-
		      ally  exclusive  with  the  remote,  local,   erspan_ver,
		      erspan, erspan_dir and erspan_hwid options.

       GENEVE Type Support
	      For  a link of type GENEVE the following additional arguments are
	      supported:

	      ip link add DEVICE type geneve id VNI remote IPADDR [ ttl TTL ] [
	      tos TOS ] [ df DF ] [ flowlabel FLOWLABEL ] [ dstport  PORT  ]  [
	      [no]external   ]	 [  [no]udpcsum	 ]  [  [no]udp6zerocsumtx  ]  [
	      [no]udp6zerocsumrx ] [ innerprotoinherit ]

		      id VNI - specifies the Virtual Network Identifier to use.

		      remote IPADDR - specifies the unicast destination IP  ad-
		      dress to use in outgoing packets.

		      ttl  TTL	-  specifies  the  TTL value to use in outgoing
		      packets. "0" or "auto" means use whatever default	 value,
		      "inherit" means inherit the inner protocol's ttl. Default
		      option is "0".

		      tos  TOS	-  specifies  the  TOS value to use in outgoing
		      packets.

		      df DF - specifies the usage of the  Don't	 Fragment  flag
		      (DF) bit in outgoing packets with IPv4 headers. The value
		      inherit  causes the bit to be copied from the original IP
		      header. The values unset and set cause the bit to be  al-
		      ways  unset  or always set, respectively. By default, the
		      bit is not set.

		      flowlabel FLOWLABEL - specifies the flow label to use  in
		      outgoing packets.

		      dstport  PORT  - select a destination port other than the
		      default of 6081.

		      [no]external - make this tunnel externally controlled (or
		      not, which is the default). This flag is mutually	 exclu-
		      sive with the id, remote, ttl, tos and flowlabel options.

		      [no]udpcsum - specifies if UDP checksum is calculated for
		      transmitted packets over IPv4.

		      [no]udp6zerocsumtx  -  skip  UDP checksum calculation for
		      transmitted packets over IPv6.

		      [no]udp6zerocsumrx - allow incoming UDP packets over IPv6
		      with zero checksum field.

		      innerprotoinherit - use IPv4/IPv6 as inner  protocol  in-
		      stead of Ethernet.

       Bareudp Type Support
	      For a link of type Bareudp the following additional arguments are
	      supported:

	      ip  link	add  DEVICE type bareudp dstport PORT ethertype PROTO [
	      srcportmin PORT ] [ [no]multiproto ]

		      dstport PORT - specifies the destination port for the UDP
		      tunnel.

		      ethertype PROTO - specifies the ethertype of the L3  pro-
		      tocol  being  tunnelled.	ethertype can be given as plain
		      Ethernet protocol	 number	 or  using  the	 protocol  name
		      ("ipv4", "ipv6", "mpls_uc", etc.).

		      srcportmin  PORT	-  selects  the lowest value of the UDP
		      tunnel source port range.

		      [no]multiproto - activates support for protocols	similar
		      to  the  one  specified  by ethertype.  When ethertype is
		      "mpls_uc" (that is, unicast MPLS), this allows the tunnel
		      to also handle multicast MPLS.  When ethertype is "ipv4",
		      this allows the tunnel to also handle IPv6.  This	 option
		      is disabled by default.

       AMT Type Support
	      For  a  link  of	type AMT the following additional arguments are
	      supported:

	      ip link add DEVICE type AMT discovery IPADDR mode { gateway | re-
	      lay } local IPADDR dev PHYS_DEV  [  relay_port  PORT  ]  [  gate-
	      way_port PORT ] [ max_tunnels NUMBER ]

		      discovery IPADDR - specifies the unicast discovery IP ad-
		      dress to use to find remote IP address.

		      mode  {  gateway	|  relay } - specifies the role of AMT,
		      Gateway or Relay

		      local IPADDR - specifies the source IP address to use  in
		      outgoing packets.

		      dev  PHYS_DEV  - specifies the underlying physical inter-
		      face from which transform traffic is sent and received.

		      relay_port PORT - specifies the UDP Relay port to	 commu-
		      nicate to the Relay.

		      gateway_port  PORT  -  specifies	the UDP Gateway port to
		      communicate to the Gateway.

		      max_tunnels NUMBER - specifies the maximum number of tun-
		      nels.

       MACVLAN and MACVTAP Type Support
	      For a link of type MACVLAN or MACVTAP  the  following  additional
	      arguments are supported:

	      ip link add link DEVICE name NAME type { macvlan | macvtap } mode
	      {	 private  |  vepa | bridge | passthru  [ nopromisc ] | source [
	      nodst ] }	 [ bcqueuelen { LENGTH } ]  [ bclim LIMIT ]

		      type { macvlan | macvtap } - specifies the link  type  to
		      use.   macvlan  creates  just  a virtual interface, while
		      macvtap in addition creates a character device  /dev/tapX
		      to be used just like a tuntap device.

		      mode private - Do not allow communication between macvlan
		      instances on the same physical interface, even if the ex-
		      ternal switch supports hairpin mode.

		      mode  vepa  - Virtual Ethernet Port Aggregator mode. Data
		      from one macvlan instance to the other on the same physi-
		      cal interface is transmitted over the physical interface.
		      Either the attached switch needs to support hairpin mode,
		      or there must be a TCP/IP router forwarding  the	packets
		      in  order	 to  allow  communication.  This is the default
		      mode.

		      mode bridge - In bridge mode, all endpoints are  directly
		      connected	 to each other, communication is not redirected
		      through the physical interface's peer.

		      mode passthru [ nopromisc ] - This mode gives more  power
		      to  a single endpoint, usually in macvtap mode. It is not
		      allowed for more than one endpoint on the	 same  physical
		      interface.  All  traffic	will  be forwarded to this end-
		      point, allowing virtio guests to change  MAC  address  or
		      set  promiscuous mode in order to bridge the interface or
		      create vlan interfaces on top of	it.  By	 default,  this
		      mode  forces  the	 underlying  interface into promiscuous
		      mode. Passing the nopromisc flag prevents	 this,	so  the
		      promisc flag may be controlled using standard tools.

		      mode  source  [ nodst ] - allows one to set a list of al-
		      lowed mac address, which is used to match against	 source
		      mac address from received frames on underlying interface.
		      This allows creating mac based VLAN associations, instead
		      of  standard  port or tag based. The feature is useful to
		      deploy 802.1x mac based behavior, where drivers of under-
		      lying interfaces doesn't allows that. By default, packets
		      are also considered  (duplicated)	 for  destination-based
		      MACVLAN.	Passing	 the  nodst flag stops matching packets
		      from also going through the destination-based flow.

		      bcqueuelen { LENGTH } - Set the length of	 the  RX  queue
		      used  to process broadcast and multicast packets.	 LENGTH
		      must be a positive integer in the	 range	[0-4294967295].
		      Setting  a  length  of 0 will effectively drop all broad-
		      cast/multicast traffic.  If  not	specified  the	macvlan
		      driver  default  (1000)  is used.	 Note that all macvlans
		      that share the same underlying device are using the  same
		      queue.  The parameter here is a request, the actual queue
		      length used will be the maximum length that  any	macvlan
		      interface	 has requested.	 When listing device parameters
		      both the bcqueuelen parameter as well as the actual  used
		      bcqueuelen  are listed to better help the user understand
		      the setting.

		      bclim LIMIT - Set the threshold for  broadcast  queueing.
		      LIMIT  must be a 32-bit integer.	Setting this to -1 dis-
		      ables broadcast queueing altogether.  Otherwise a	 multi-
		      cast address will be queued as broadcast if the number of
		      devices using it is greater than the given value.

       High-availability Seamless Redundancy (HSR) Support
	      For  a  link  of	type HSR the following additional arguments are
	      supported:

	      ip link add link DEVICE  name  NAME  type	 hsr  slave1  SLAVE1-IF
	      slave2  SLAVE2-IF	 [ interlink INTERLINK-IF ] [ supervision ADDR-
	      BYTE ] [ version { 0 | 1 } [ proto { 0 | 1 } ]

		      type hsr - specifies the link type to use, here HSR.

		      slave1 SLAVE1-IF - Specifies the physical device used for
		      the first of the two ring ports.

		      slave2 SLAVE2-IF - Specifies the physical device used for
		      the second of the two ring ports.

		      interlink INTERLINK-IF - The interlink  device  bound  to
		      the HSR network to connect SAN device(s).

		      supervision  ADDR-BYTE  -	 The last byte of the multicast
		      address used for HSR supervision frames.	Default	 option
		      is "0", possible values 0-255.

		      version  {  0 | 1 } - Selects the protocol version of the
		      interface. Default option is "0",	 which	corresponds  to
		      the  2010	 version  of the HSR standard. Option "1" acti-
		      vates the 2012 version.

		      proto { 0 | 1 } - Selects the protocol at the  interface.
		      Default option is "0", which corresponds to the HSR stan-
		      dard. Option "1" activates the Parallel Redundancy Proto-
		      col (PRP).

       BRIDGE Type Support
	      For  a link of type BRIDGE the following additional arguments are
	      supported:

	      ip link add DEVICE type bridge  [	 ageing_time  AGEING_TIME  ]  [
	      group_fwd_mask  MASK  ] [ group_address ADDRESS ] [ forward_delay
	      FORWARD_DELAY ] [ hello_time HELLO_TIME ] [ max_age MAX_AGE  ]  [
	      stp_state STP_STATE ] [ mst_enabled MST_ENABLED ] [ priority PRI-
	      ORITY    ]    [	no_linklocal_learn   NO_LINKLOCAL_LEARN	  ]   [
	      fdb_max_learned FDB_MAX_LEARNED ] [ vlan_filtering VLAN_FILTERING
	      ] [ vlan_protocol VLAN_PROTOCOL ]	 [  vlan_default_pvid  VLAN_DE-
	      FAULT_PVID   ]   [   vlan_stats_enabled  VLAN_STATS_ENABLED  ]  [
	      vlan_stats_per_port VLAN_STATS_PER_PORT ] [ mcast_snooping MULTI-
	      CAST_SNOOPING ] [ mcast_vlan_snooping MULTICAST_VLAN_SNOOPING ] [
	      mcast_router   MULTICAST_ROUTER	]   [	 mcast_query_use_ifaddr
	      MCAST_QUERY_USE_IFADDR  ]	 [  mcast_querier MULTICAST_QUERIER ] [
	      mcast_hash_elasticity HASH_ELASTICITY ] [ mcast_hash_max HASH_MAX
	      ]	   [	mcast_last_member_count	   LAST_MEMBER_COUNT	]     [
	      mcast_startup_query_count STARTUP_QUERY_COUNT ] [ mcast_last_mem-
	      ber_interval  LAST_MEMBER_INTERVAL  ] [ mcast_membership_interval
	      MEMBERSHIP_INTERVAL ] [ mcast_querier_interval QUERIER_INTERVAL ]
	      [	 mcast_query_interval  QUERY_INTERVAL	]   [	mcast_query_re-
	      sponse_interval	      QUERY_RESPONSE_INTERVAL	     ]	      [
	      mcast_startup_query_interval    STARTUP_QUERY_INTERVAL	]     [
	      mcast_stats_enabled  MCAST_STATS_ENABLED	]  [ mcast_igmp_version
	      IGMP_VERSION ] [ mcast_mld_version MLD_VERSION ] [  nf_call_ipta-
	      bles NF_CALL_IPTABLES ] [ nf_call_ip6tables NF_CALL_IP6TABLES ] [
	      nf_call_arptables NF_CALL_ARPTABLES ]

		      ageing_time  AGEING_TIME - configure the bridge's FDB en-
		      tries ageing time, ie the number of seconds a MAC address
		      will be kept in the FDB after a packet has been  received
		      from  that  address.  after this time has passed, entries
		      are cleaned up.

		      group_fwd_mask MASK - set the group forward mask. This is
		      the bitmask that is applied to decide whether to	forward
		      incoming	frames destined to link-local addresses, ie ad-
		      dresses of the form 01:80:C2:00:00:0X (defaults to 0,  ie
		      the bridge does not forward any link-local frames).

		      group_address ADDRESS - set the MAC address of the multi-
		      cast group this bridge uses for STP.  The address must be
		      a	 link-local  address  in  standard Ethernet MAC address
		      format, ie an address of the form 01:80:C2:00:00:0X, with
		      X
		       in [0, 4..f].

		      forward_delay FORWARD_DELAY - set the forwarding delay in
		      seconds, ie the time spent  in  LISTENING	 state	(before
		      moving  to LEARNING) and in LEARNING state (before moving
		      to FORWARDING). Only relevant if STP  is	enabled.  Valid
		      values are between 2 and 30.

		      hello_time  HELLO_TIME  - set the time in seconds between
		      hello packets sent by the	 bridge,  when	it  is	a  root
		      bridge  or a designated bridges.	Only relevant if STP is
		      enabled. Valid values are between 1 and 10.

		      max_age MAX_AGE - set the hello packet  timeout,	ie  the
		      time in seconds until another bridge in the spanning tree
		      is  assumed to be dead, after reception of its last hello
		      message. Only relevant if STP is	enabled.  Valid	 values
		      are between 6 and 40.

		      stp_state	 STP_STATE  -  turn  spanning  tree protocol on
		      (STP_STATE > 0)  or  off	(STP_STATE  ==	0).   for  this
		      bridge.

		      mst_enabled  MST_ENABLED	-  turn	 multiple spanning tree
		      (MST) support on (MST_ENABLED > 0) or off (MST_ENABLED ==
		      0).  When enabled, sets of VLANs can be  associated  with
		      multiple	spanning tree instances (MSTIs), and STP states
		      for each port can be  controlled	on  a  per-MSTI	 basis.
		      Note: no implementation of the MSTP protocol is provided,
		      only  the primitives needed to implement it. To avoid in-
		      terfering with the legacy per-VLAN STP states, this  set-
		      ting can only be changed when no bridge VLANs are config-
		      ured.

		      priority	PRIORITY - set this bridge's spanning tree pri-
		      ority, used during STP root bridge election.  PRIORITY is
		      a 16bit unsigned integer.

		      no_linklocal_learn NO_LINKLOCAL_LEARN -  turn  link-local
		      learning	on (NO_LINKLOCAL_LEARN == 0) or off (NO_LINKLO-
		      CAL_LEARN > 0).  When disabled, the bridge will not learn
		      from link-local frames (default: enabled).

		      fdb_max_learned FDB_MAX_LEARNED - set the maximum	 number
		      of  learned  FDB	entries.  If (FDB_MAX_LEARNED == 0) the
		      feature is disabled. Default is 0.  FDB_MAX_LEARNED is  a
		      32bit unsigned integer.

		      vlan_filtering  VLAN_FILTERING  -	 turn VLAN filtering on
		      (VLAN_FILTERING > 0) or off (VLAN_FILTERING == 0).   When
		      disabled,	 the bridge will not consider the VLAN tag when
		      handling packets.

		      vlan_protocol { 802.1Q | 802.1ad }  -  set  the  protocol
		      used for VLAN filtering.

		      vlan_default_pvid	 VLAN_DEFAULT_PVID  -  set  the default
		      PVID (native/untagged VLAN ID) for this bridge.

		      vlan_stats_enabled    VLAN_STATS_ENABLED	   -	 enable
		      (VLAN_STATS_ENABLED  == 1) or disable (VLAN_STATS_ENABLED
		      == 0) per-VLAN stats accounting.

		      vlan_stats_per_port    VLAN_STATS_PER_PORT    -	 enable
		      (VLAN_STATS_PER_PORT	==	1)	or	disable
		      (VLAN_STATS_PER_PORT == 0) per-VLAN  per-port  stats  ac-
		      counting.	 Can  be  changed  only	 when there are no port
		      VLANs configured.

		      mcast_snooping MULTICAST_SNOOPING - turn multicast snoop-
		      ing on (MULTICAST_SNOOPING > 0) or off  (MULTICAST_SNOOP-
		      ING == 0).

		      mcast_vlan_snooping MULTICAST_VLAN_SNOOPING - turn multi-
		      cast  VLAN  snooping  on (MULTICAST_VLAN_SNOOPING > 0) or
		      off (MULTICAST_VLAN_SNOOPING == 0).

		      mcast_router MULTICAST_ROUTER -  set  bridge's  multicast
		      router  if IGMP snooping is enabled.  MULTICAST_ROUTER is
		      an integer value having the following meaning:

			      0 - disabled.

			      1 - automatic (queried).

			      2 - permanently enabled.

		      mcast_query_use_ifaddr MCAST_QUERY_USE_IFADDR  -	whether
		      to  use the bridge's own IP address as source address for
		      IGMP queries (MCAST_QUERY_USE_IFADDR > 0) or the	default
		      of 0.0.0.0 (MCAST_QUERY_USE_IFADDR == 0).

		      mcast_querier    MULTICAST_QUERIER   -   enable	(MULTI-
		      CAST_QUERIER > 0) or  disable  (MULTICAST_QUERIER	 ==  0)
		      IGMP  querier,  ie  sending  of  multicast queries by the
		      bridge (default: disabled).

		      mcast_querier_interval QUERIER_INTERVAL  -  interval  be-
		      tween  queries  sent  by other routers. if no queries are
		      seen after this delay has passed, the bridge  will  start
		      to  send	its  own  queries  (as if mcast_querier was en-
		      abled).

		      mcast_hash_elasticity  HASH_ELASTICITY  -	 set  multicast
		      database	hash elasticity, ie the maximum chain length in
		      the multicast hash table (defaults to 4).

		      mcast_hash_max HASH_MAX - set maximum size  of  multicast
		      hash table (defaults to 512, value must be a power of 2).

		      mcast_last_member_count LAST_MEMBER_COUNT - set multicast
		      last  member  count,  ie the number of queries the bridge
		      will send before stopping forwarding  a  multicast  group
		      after  a	"leave"	 message has been received (defaults to
		      2).

		      mcast_last_member_interval LAST_MEMBER_INTERVAL -	 inter-
		      val between queries to find remaining members of a group,
		      after a "leave" message is received.

		      mcast_startup_query_count	 STARTUP_QUERY_COUNT  - set the
		      number of IGMP queries to send during startup phase  (de-
		      faults to 2).

		      mcast_startup_query_interval STARTUP_QUERY_INTERVAL - in-
		      terval between queries in the startup phase.

		      mcast_query_interval  QUERY_INTERVAL  -  interval between
		      queries sent by the bridge after the end of  the	startup
		      phase.

		      mcast_query_response_interval  QUERY_RESPONSE_INTERVAL  -
		      set the Max  Response  Time/Maximum  Response  Delay  for
		      IGMP/MLD queries sent by the bridge.

		      mcast_membership_interval MEMBERSHIP_INTERVAL - delay af-
		      ter which the bridge will leave a group, if no membership
		      reports for this group are received.

		      mcast_stats_enabled    MCAST_STATS_ENABLED    -	 enable
		      (MCAST_STATS_ENABLED > 0) or disable (MCAST_STATS_ENABLED
		      == 0) multicast (IGMP/MLD) stats accounting.

		      mcast_igmp_version IGMP_VERSION - set the IGMP version.

		      mcast_mld_version MLD_VERSION - set the MLD version.

		      nf_call_iptables NF_CALL_IPTABLES - enable (NF_CALL_IPTA-
		      BLES > 0) or disable  (NF_CALL_IPTABLES  ==  0)  iptables
		      hooks on the bridge.

		      nf_call_ip6tables	     NF_CALL_IP6TABLES	   -	 enable
		      (NF_CALL_IP6TABLES > 0) or disable (NF_CALL_IP6TABLES  ==
		      0) ip6tables hooks on the bridge.

		      nf_call_arptables	     NF_CALL_ARPTABLES	   -	 enable
		      (NF_CALL_ARPTABLES > 0) or disable (NF_CALL_ARPTABLES  ==
		      0) arptables hooks on the bridge.

       MACsec Type Support
	      For  a link of type MACsec the following additional arguments are
	      supported:

	      ip link add link	DEVICE	name  NAME  type  macsec  [  [	address
	      <lladdr> ] port PORT | sci SCI ] [ cipher CIPHER_SUITE ] [ icvlen
	      {	 8..16 } ] [ encrypt { on | off } ] [ send_sci { on | off } ] [
	      end_station { on | off } ] [ scb { on | off } ] [ protect { on  |
	      off } ] [ replay { on | off } window { 0..2^32-1 } ] [ validate {
	      strict | check | disabled } ] [ encodingsa { 0..3 } ]

		      address  <lladdr>	 - sets the system identifier component
		      of secure channel for this MACsec device.

		      port PORT - sets the  port  number  component  of	 secure
		      channel  for  this  MACsec  device,  in a range from 1 to
		      65535 inclusive. Numbers with a leading " 0 " or "  0x  "
		      are interpreted as octal and hexadecimal, respectively.

		      sci  SCI	-  sets	 the secure channel identifier for this
		      MACsec device.  SCI is a 64bit wide number in hexadecimal
		      format.

		      cipher CIPHER_SUITE - defines the cipher suite to use.

		      icvlen LENGTH - sets the length of  the  Integrity  Check
		      Value (ICV).

		      encrypt  on  or  encrypt off - switches between authenti-
		      cated encryption, or authenticity mode only.

		      send_sci on or send_sci off - specifies whether  the  SCI
		      is  included  in	every packet, or only when it is neces-
		      sary.

		      end_station on or end_station off - sets the End	Station
		      bit.

		      scb on or scb off - sets the Single Copy Broadcast bit.

		      protect  on or protect off - enables MACsec protection on
		      the device.

		      replay on or replay off - enables	 replay	 protection  on
		      the device.

			      window SIZE - sets the size of the replay window.

		      validate	strict or validate check or validate disabled -
		      sets the validation mode on the device.

		      encodingsa AN - sets the active  secure  association  for
		      transmission.

       VRF Type Support
	      For  a  link  of	type VRF the following additional arguments are
	      supported:

	      ip link add DEVICE type vrf table TABLE

		      table table id associated with VRF device

       RMNET Type Support
	      For a link of type RMNET the following additional	 arguments  are
	      supported:

	      ip link add link DEVICE name NAME type rmnet mux_id MUXID

		      mux_id MUXID - specifies the mux identifier for the rmnet
		      device, possible values 1-254.

       XFRM Type Support
	      For  a  link  of type XFRM the following additional arguments are
	      supported:

	      ip link add DEVICE type xfrm dev PHYS_DEV [ if_id IF_ID ]	 [  ex-
	      ternal ]

		      dev  PHYS_DEV  - specifies the underlying physical inter-
		      face from which transform traffic is sent and received.

		      if_id IF-ID - specifies the hexadecimal lookup  key  used
		      to send traffic to and from specific xfrm policies. Poli-
		      cies  must  be  configured with the same key. If not set,
		      the key defaults to 0 and will match any	policies  which
		      similarly do not have a lookup key configuration.

		      external	-  make this device externally controlled. This
		      flag is mutually exclusive with the  dev	and  if_id  op-
		      tions.

       GTP Type Support
	      For  a  link  of	type GTP the following additional arguments are
	      supported:

	      ip link add DEVICE type gtp role ROLE hsize HSIZE

		      role ROLE - specifies the role of the GTP device,	 either
		      sgsn or ggsn

		      hsize  HSIZE  -  specifies  size	of  the hashtable which
		      stores PDP contexts

		      restart_count  RESTART_COUNT  -  GTP   instance	restart
		      counter

       PFCP Type Support
	      For a link of type PFCP no additional arguments are supported

   ip link delete - delete virtual link
       dev DEVICE
	      specifies the virtual device to act operate on.

       group GROUP
	      specifies	 the  group  of virtual links to delete. Group 0 is not
	      allowed to be deleted since it is the default group.

       type TYPE
	      specifies the type of the device.

   ip link set - change device attributes
       Warning: If multiple parameter changes are requested, ip aborts	immedi-
       ately  after any of the changes have failed.  This is the only case when
       ip can move the system to an unpredictable state.  The  solution	 is  to
       avoid  changing several parameters with one ip link set call.  The modi-
       fier change is equivalent to set.

       dev DEVICE
	      DEVICE specifies network device to operate on.  When  configuring
	      SR-IOV Virtual Function (VF) devices, this keyword should specify
	      the associated Physical Function (PF) device.

       group GROUP
	      GROUP  has  a  dual role: If both group and dev are present, then
	      move the device to the specified group. If only a group is speci-
	      fied, then the command operates on all devices in that group.

       up and down
	      change the state of the device to UP or DOWN.

       arp on or arp off
	      change the NOARP flag on the device.

       multicast on or multicast off
	      change the MULTICAST flag on the device.

       allmulticast on or allmulticast off
	      change the ALLMULTI flag on the device. When  enabled,  instructs
	      network driver to retrieve all multicast packets from the network
	      to the kernel for further processing.

       promisc on or promisc off
	      change  the  PROMISC  flag on the device. When enabled, activates
	      promiscuous operation of the network device.

       trailers on or trailers off
	      change the NOTRAILERS flag on the device, NOT used by  the  Linux
	      and exists for BSD compatibility.

       protodown on or protodown off
	      change the PROTODOWN state on the device. Indicates that a proto-
	      col error has been detected on the port. Switch drivers can react
	      to this error by doing a phys down on the switch port.

       protodown_reason PREASON on or off
	      set  PROTODOWN  reasons on the device. protodown reason bit names
	      can be enumerated under /etc/iproute2/protodown_reasons.d/.  pos-
	      sible reasons bits 0-31

       dynamic on or dynamic off
	      change the DYNAMIC flag on the device. Indicates that address can
	      change  when  interface  goes  down  (currently  NOT  used by the
	      Linux).

       name NAME
	      change the name of the device. This operation is not  recommended
	      if  the  device  is running or has some addresses already config-
	      ured.

       txqueuelen NUMBER

       txqlen NUMBER
	      change the transmit queue length of the device.

       mtu NUMBER
	      change the MTU of the device.

       address LLADDRESS
	      change the station address of the interface.

       broadcast LLADDRESS

       brd LLADDRESS

       peer LLADDRESS
	      change the link layer broadcast address or the peer address  when
	      the interface is POINTOPOINT.

       netns  { PID | NETNSNAME | NETNSFILE }
	      move  the device to the network namespace associated with process
	      PID or the name NETNSNAME or the file NETNSFILE.

	      Some devices are not allowed to change network  namespace:  loop-
	      back,  bridge,  wireless.	 These	are network namespace local de-
	      vices. In such case ip tool will return "Invalid argument" error.
	      It is possible to find out if device is local to a single network
	      namespace by checking netns-local flag in the output of the  eth-
	      tool:

		      ethtool -k DEVICE

	      To  change network namespace for wireless devices the iw tool can
	      be used. But it allows one to change network namespace  only  for
	      physical devices and by process PID.

       alias NAME
	      give the device a symbolic name for easy reference.

       group GROUP
	      specify  the  group  the device belongs to.  The available groups
	      are listed in  /usr/share/iproute2/group	or  /etc/iproute2/group
	      (has precedence if exists).

       vf NUM specify  a  Virtual Function device to be configured. The associ-
	      ated PF device must be specified using the dev parameter.

		      mac LLADDRESS - change the station address for the speci-
		      fied VF. The vf parameter must be specified.

		      vlan VLANID - change the assigned VLAN for the  specified
		      VF.  When specified, all traffic sent from the VF will be
		      tagged with the specified VLAN ID. Incoming traffic  will
		      be  filtered for the specified VLAN ID, and will have all
		      VLAN tags stripped before being passed to the VF. Setting
		      this parameter to 0 disables VLAN tagging and  filtering.
		      The vf parameter must be specified.

		      qos  VLAN-QOS  -	assign VLAN QOS (priority) bits for the
		      VLAN tag. When specified, all VLAN  tags	transmitted  by
		      the  VF  will  include the specified priority bits in the
		      VLAN tag. If not specified, the value is assumed to be 0.
		      Both the vf and vlan parameters must be  specified.  Set-
		      ting  both  vlan	and  qos as 0 disables VLAN tagging and
		      filtering for the VF.

		      proto VLAN-PROTO - assign VLAN PROTOCOL for the VLAN tag,
		      either 802.1Q or 802.1ad.	 Setting to 802.1ad, all  traf-
		      fic sent from the VF will be tagged with VLAN S-Tag.  In-
		      coming  traffic will have VLAN S-Tags stripped before be-
		      ing passed to the VF.  Setting to 802.1ad also enables an
		      option to concatenate another VLAN tag, so both S-TAG and
		      C-TAG will  be  inserted/stripped	 for  outgoing/incoming
		      traffic,	respectively.	If  not specified, the value is
		      assumed to be 802.1Q. Both the  vf  and  vlan  parameters
		      must be specified.

		      rate  TXRATE -- change the allowed transmit bandwidth, in
		      Mbps, for the specified VF.  Setting this parameter to  0
		      disables	rate limiting.	vf parameter must be specified.
		      Please use new API max_tx_rate option instead.

		      max_tx_rate TXRATE - change the allowed maximum  transmit
		      bandwidth,  in  Mbps, for the specified VF.  Setting this
		      parameter to 0 disables rate limiting.  vf parameter must
		      be specified.

		      min_tx_rate TXRATE - change the allowed minimum  transmit
		      bandwidth, in Mbps, for the specified VF.	 Minimum TXRATE
		      should be always <= Maximum TXRATE.  Setting this parame-
		      ter  to  0  disables rate limiting.  vf parameter must be
		      specified.

		      spoofchk on|off - turn packet spoof checking  on	or  off
		      for the specified VF.

		      query_rss on|off - toggle the ability of querying the RSS
		      configuration  of	 a specific VF. VF RSS information like
		      RSS hash key may be considered sensitive on some	devices
		      where  this  information	is shared between VF and PF and
		      thus its querying may be prohibited by default.

		      state auto|enable|disable - set the virtual link state as
		      seen by the specified VF. Setting to auto means a reflec-
		      tion of the PF link state, enable lets the VF to communi-
		      cate with other VFs on this host	even  if  the  PF  link
		      state  is down, disable causes the HW to drop any packets
		      sent by the VF.

		      trust on|off - trust the specified VF user. This	enables
		      that  VF user can set a specific feature which may impact
		      security and/or performance. (e.g. VF multicast promiscu-
		      ous mode)

		      node_guid eui64 - configure node GUID for Infiniband VFs.

		      port_guid eui64 - configure port GUID for Infiniband VFs.

       xdp object | pinned | off
	      set (or unset) a XDP ("eXpress Data Path") BPF program to run  on
	      every packet at driver level.  ip link output will indicate a xdp
	      flag  for	 the networking device. If the driver does not have na-
	      tive XDP support, the kernel will fall back to a slower,	driver-
	      independent  "generic"  XDP  variant.  The ip link output will in
	      that case indicate xdpgeneric instead of xdp only. If the	 driver
	      does  have  native  XDP  support, but the program is loaded under
	      xdpgeneric object | pinned then the kernel will use  the	generic
	      XDP  variant  instead of the native one.	xdpdrv has the opposite
	      effect of requesting that the automatic fallback to  the	generic
	      XDP variant be disabled and in case driver is not XDP-capable er-
	      ror  should be returned.	xdpdrv also disables hardware offloads.
	      xdpoffload in ip link output indicates that the program has  been
	      offloaded	 to  hardware  and can also be used to request the "of-
	      fload" mode, much like xdpgeneric it forces  program  to	be  in-
	      stalled specifically in HW/FW of the adapter.

	      off  (or none ) - Detaches any currently attached XDP/BPF program
	      from the given device.

	      object FILE - Attaches a XDP/BPF program to the given device. The
	      FILE points to a BPF ELF file (f.e. generated by LLVM) that  con-
	      tains the BPF program code, map specifications, etc. If a XDP/BPF
	      program is already attached to the given device, an error will be
	      thrown.  If  no XDP/BPF program is currently attached, the device
	      supports XDP and the program from the BPF	 ELF  file  passes  the
	      kernel  verifier,	 then it will be attached to the device. If the
	      option -force is passed to ip then  any  prior  attached	XDP/BPF
	      program will be atomically overridden and no error will be thrown
	      in  this	case.  If no section option is passed, then the default
	      section name ("prog") will be  assumed,  otherwise  the  provided
	      section name will be used. If no verbose option is passed, then a
	      verifier	log  will only be dumped on load error.	 See also EXAM-
	      PLES section for usage examples.

	      section NAME - Specifies a section name  that  contains  the  BPF
	      program  code.  If  no section name is specified, the default one
	      ("prog") will be used. This option is to be passed with  the  ob-
	      ject option.

	      program NAME - Specifies the BPF program name that need to be at-
	      tached.  When the program name is specified, the section name pa-
	      rameter will be ignored. This option  only  works	 when  iproute2
	      build with libbpf support.

	      verbose  - Act in verbose mode. For example, even in case of suc-
	      cess, this will print the verifier log  in  case	a  program  was
	      loaded from a BPF ELF file.

	      pinned FILE - Attaches a XDP/BPF program to the given device. The
	      FILE points to an already pinned BPF program in the BPF file sys-
	      tem.  The option section doesn't apply here, but otherwise seman-
	      tics are the same as with the option object described already.

       master DEVICE
	      set master device of the device (enslave device).

       nomaster
	      unset master device of the device (release device).

       addrgenmode eui64|none|stable_secret|random
	      set the IPv6 address generation mode

	      eui64 - use a Modified EUI-64 format interface identifier

	      none - disable automatic address generation

	      stable_secret - generate the interface identifier based on a pre-
	      set
		/proc/sys/net/ipv6/conf/{default,DEVICE}/stable_secret

	      random - like stable_secret, but auto-generate a new  random  se-
	      cret if none is set

       link-netnsid
	      set peer netnsid for a cross-netns interface

       type ETYPE TYPE_ARGS
	      Change  type-specific settings. For a list of supported types and
	      arguments refer to the description of ip link add above. In addi-
	      tion to that, it is possible to manipulate settings to slave  de-
	      vices:

       Bridge Slave Support
	      For  a link with master bridge the following additional arguments
	      are supported:

	      ip link set type bridge_slave [ fdb_flush ] [  state  STATE  ]  [
	      priority	PRIO ] [ cost COST ] [ guard { on | off } ] [ hairpin {
	      on | off } ] [ fastleave { on | off } ] [ root_block { on | off }
	      ] [ learning { on | off } ] [ flood { on | off } ] [ proxy_arp  {
	      on  | off } ] [ proxy_arp_wifi { on | off } ] [ mcast_router MUL-
	      TICAST_ROUTER ] [ mcast_fast_leave { on | off} ] [ bcast_flood  {
	      on | off } ] [ mcast_flood { on | off } ] [ mcast_to_unicast { on
	      | off } ] [ group_fwd_mask MASK ] [ neigh_suppress { on | off } ]
	      [ neigh_vlan_suppress { on | off } ] [ vlan_tunnel { on | off } ]
	      [	 isolated  {  on | off } ] [ locked { on | off } ] [ mab { on |
	      off } ] [ backup_port DEVICE ] [ nobackup_port  ]	 [  backup_nhid
	      NHID ]

		      fdb_flush - flush bridge slave's fdb dynamic entries.

		      state  STATE  - Set port state.  STATE is a number repre-
		      senting the following states: 0  (disabled),  1  (listen-
		      ing), 2 (learning), 3 (forwarding), 4 (blocking).

		      priority PRIO - set port priority (allowed values are be-
		      tween 0 and 63, inclusively).

		      cost  COST  - set port cost (allowed values are between 1
		      and 65535, inclusively).

		      guard { on | off } - block incoming BPDU packets on  this
		      port.

		      hairpin  { on | off } - enable hairpin mode on this port.
		      This will allow incoming packets on this port to	be  re-
		      flected back.

		      fastleave	 {  on | off } - enable multicast fast leave on
		      this port.

		      root_block { on | off } - block this port	 from  becoming
		      the bridge's root port.

		      learning	{  on  |  off } - allow MAC address learning on
		      this port.

		      flood { on | off } - open the flood gates on  this  port,
		      i.e.  forward  all  unicast frames to this port also. Re-
		      quires proxy_arp and proxy_arp_wifi to be turned off.

		      proxy_arp { on | off } - enable proxy ARP on this port.

		      proxy_arp_wifi { on | off } - enable proxy  ARP  on  this
		      port which meets extended requirements by IEEE 802.11 and
		      Hotspot 2.0 specifications.

		      mcast_router  MULTICAST_ROUTER  - configure this port for
		      having multicast routers attached. A port with  a	 multi-
		      cast  router  will receive all multicast traffic.	 MULTI-
		      CAST_ROUTER may be either 0 to disable multicast	routers
		      on  this port, 1 to let the system detect the presence of
		      routers (this is the default), 2	to  permanently	 enable
		      multicast	 traffic forwarding on this port or 3 to enable
		      multicast routers temporarily on this port, not depending
		      on incoming queries.

		      mcast_fast_leave { on | off } - this is a synonym to  the
		      fastleave option above.

		      bcast_flood { on | off } - controls flooding of broadcast
		      traffic on the given port. By default this flag is on.

		      mcast_flood  { on | off } - controls whether a given port
		      will flood multicast traffic for which there  is	no  MDB
		      entry. By default this flag is on.

		      mcast_to_unicast	{ on | off } - controls whether a given
		      port will replicate packets using unicast instead of mul-
		      ticast. By default this flag is off.

		      group_fwd_mask MASK - set the group forward mask. This is
		      the bitmask that is applied to decide whether to	forward
		      incoming	frames destined to link-local addresses, ie ad-
		      dresses of the form 01:80:C2:00:00:0X (defaults to 0,  ie
		      the  bridge does not forward any link-local frames coming
		      on this port).

		      neigh_suppress { on | off } - controls whether neigh dis-
		      covery (arp and nd) proxy and suppression is  enabled  on
		      the port. By default this flag is off.

		      neigh_vlan_suppress  { on | off } - controls whether per-
		      VLAN neigh discovery (arp and nd) proxy  and  suppression
		      is  enabled  on the port. When on, the bridge link option
		      neigh_suppress has no effect and the  per-VLAN  state  is
		      set  using  the bridge vlan option neigh_suppress. By de-
		      fault this flag is off.

		      vlan_tunnel { on | off } - controls whether vlan to  tun-
		      nel  mapping is enabled on the port. By default this flag
		      is off.

		      locked { on | off } - controls whether a port  is	 locked
		      or  not.	When  locked,  non-link-local  frames  received
		      through the port are dropped unless an FDB entry with the
		      MAC source address points to the	port.  The  common  use
		      case  is	IEEE  802.1X where hosts can authenticate them-
		      selves by exchanging EAPOL frames with an	 authenticator.
		      After  authentication is complete, the user space control
		      plane can install a matching FDB entry to	 allow	traffic
		      from  the host to be forwarded by the bridge. When learn-
		      ing is enabled on a locked port,	the  no_linklocal_learn
		      bridge  option  needs to be on to prevent the bridge from
		      learning from received EAPOL frames. By default this flag
		      is off.

		      mab { on | off } - controls  whether  MAC	 Authentication
		      Bypass (MAB) is enabled on the port or not.  MAB can only
		      be  enabled  on  a locked port that has learning enabled.
		      When enabled, FDB entries are learned from received traf-
		      fic and have the "locked" FDB flag set. The flag can only
		      be set by the kernel and it indicates that the FDB  entry
		      cannot  be  used	to authenticate the corresponding host.
		      User space can decide to authenticate the host by replac-
		      ing the FDB entry and clearing  the  "locked"  FDB  flag.
		      Locked  FDB  entries  can	 roam  to unlocked (authorized)
		      ports in which case the "locked" flag is cleared. FDB en-
		      tries cannot roam to locked ports regardless of MAB being
		      enabled or not. Therefore, locked FDB  entries  are  only
		      created  if  an  FDB entry with the given {MAC, VID} does
		      not already exist.  This	behavior  prevents  unauthenti-
		      cated  hosts  from disrupting traffic destined to already
		      authenticated hosts. Locked FDB entries act like	regular
		      dynamic  entries with respect to forwarding and aging. By
		      default this flag is off.

		      backup_port DEVICE - if the port loses carrier all  traf-
		      fic will be redirected to the configured backup port

		      nobackup_port  -	removes the currently configured backup
		      port

		      backup_nhid NHID - the FDB nexthop object ID (see ip-nex-
		      thop(8)) to attach  to  packets  being  redirected  to  a
		      backup port that has VLAN tunnel mapping enabled (via the
		      vlan_tunnel  option).  Setting a value of 0 (default) has
		      the effect of not attaching any ID.

       Bonding Slave Support
	      For a link with master bond the  following  additional  arguments
	      are supported:

	      ip link set type bond_slave [ queue_id ID ] [ prio PRIORITY ]

		      queue_id	ID - set the slave's queue ID (a 16bit unsigned
		      value).

		      prio PRIORITY - set the slave's priority for active slave
		      re-selection during failover (a 32bit signed value). This
		      option only valid for active-backup(1),  balance-tlb  (5)
		      and balance-alb (6) mode.

       MACVLAN and MACVTAP Support
	      Modify list of allowed macaddr for link in source mode.

	      ip  link	set type { macvlan | macvap } [ macaddr COMMAND MACADDR
	      ...  ]

	      Commands:
		      add - add MACADDR to allowed list

		      set - replace allowed list

		      del - remove MACADDR from allowed list

		      flush - flush whole allowed list

	      Update the broadcast/multicast queue length.

	      ip link set type { macvlan | macvap } [ bcqueuelen   LENGTH  ]  [
	      bclim LIMIT ]

		      bcqueuelen  LENGTH  - Set the length of the RX queue used
		      to process broadcast and multicast packets.  LENGTH  must
		      be  a positive integer in the range [0-4294967295].  Set-
		      ting a length of	0  will	 effectively  drop  all	 broad-
		      cast/multicast  traffic.	 If  not  specified the macvlan
		      driver default (1000) is used.  Note  that  all  macvlans
		      that  share the same underlying device are using the same
		      queue. The parameter here is a request, the actual  queue
		      length  used  will be the maximum length that any macvlan
		      interface has requested.	When listing device  parameters
		      both  the bcqueuelen parameter as well as the actual used
		      bcqueuelen are listed to better help the user  understand
		      the setting.

		      bclim  LIMIT  - Set the threshold for broadcast queueing.
		      LIMIT must be a 32-bit integer.  Setting this to -1  dis-
		      ables  broadcast queueing altogether.  Otherwise a multi-
		      cast address will be queued as broadcast if the number of
		      devices using it is greater than the given value.

       DSA user port support
	      For a link having the DSA user port  type,  the  following  addi-
	      tional arguments are supported:

	      ip link set type dsa [ conduit DEVICE ]

		      conduit DEVICE - change the DSA conduit (host network in-
		      terface)	responsible for handling the locally terminated
		      traffic for the given DSA switch user  port.  For	 a  de-
		      scription	 of  which  network interfaces are suitable for
		      serving as conduit interfaces of this user  port,	 please
		      see     https://docs.kernel.org/networking/dsa/configura-
		      tion.html#affinity-of-user-ports-to-cpu-ports as well  as
		      what is supported by the driver in use.

		      master DEVICE - this is a synonym for "conduit".

   ip link show - display device attributes
       dev NAME (default)
	      NAME specifies the network device to show.

       group GROUP
	      GROUP specifies what group of devices to show.

       up     only display running interfaces.

       down   only display not running interfaces.

       master DEVICE
	      DEVICE  specifies	 the  master  device  which enslaves devices to
	      show.

       vrf NAME
	      NAME specifies the VRF which enslaves devices to show.

       type TYPE
	      TYPE specifies the type of devices to show.

	      Note that the type name is not checked against the list  of  sup-
	      ported  types  - instead it is sent as-is to the kernel. Later it
	      is used to filter the returned interface	list  by  comparing  it
	      with  the relevant attribute in case the kernel didn't filter al-
	      ready. Therefore any string is accepted, but may	lead  to  empty
	      output.

       nomaster
	      only show devices with no master

       novf   only show devices with no VF info

   ip link xstats - display extended statistics
       type TYPE
	      TYPE specifies the type of devices to display extended statistics
	      for.

   ip link afstats - display address-family specific statistics
       dev DEVICE
	      DEVICE  specifies the device to display address-family statistics
	      for.

   ip link help - display help
       TYPE specifies which help of link type to display.

   GROUP
       may  be	a  number  or  a  string  from	 /usr/share/iproute2/group   or
       /etc/iproute2/group  which  can be manually filled and has precedence if
       exists.

EXAMPLES
       ip link show
	   Shows the state of all network interfaces on the system.

       ip link show type bridge
	   Shows the bridge devices.

       ip link show type vlan
	   Shows the vlan devices.

       ip link show master br0
	   Shows devices enslaved by br0

       ip link set dev ppp0 mtu 1400
	   Change the MTU the ppp0 device.

       ip link add link eth0 name eth0.10 type vlan id 10
	   Creates a new vlan device eth0.10 on device eth0.

       ip link delete dev eth0.10
	   Removes vlan device.

       ip link help gre
	   Display help for the gre link type.

       ip link add name tun1 type ipip remote 192.168.1.1 local 192.168.1.2 ttl
       225 encap gue encap-sport auto encap-dport 5555 encap-csum encap-remcsum
	   Creates an IPIP that is encapsulated with Generic UDP Encapsulation,
	   and the outer UDP checksum and remote checksum offload are enabled.

       ip link set dev eth0 xdp obj prog.o
	   Attaches a XDP/BPF program to device eth0, where the program is  lo-
	   cated in prog.o, section "prog" (default section). In case a XDP/BPF
	   program is already attached, throw an error.

       ip -force link set dev eth0 xdp obj prog.o sec foo
	   Attaches  a XDP/BPF program to device eth0, where the program is lo-
	   cated in prog.o, section "foo". In case a XDP/BPF program is already
	   attached, it will be overridden by the new one.

       ip -force link set dev eth0 xdp pinned /sys/fs/bpf/foo
	   Attaches a XDP/BPF program to device eth0,  where  the  program  was
	   previously  pinned as an object node into BPF file system under name
	   foo.

       ip link set dev eth0 xdp off
	   If a XDP/BPF program is attached on device eth0, detach it  and  ef-
	   fectively turn off XDP for device eth0.

       ip link add link wpan0 lowpan0 type lowpan
	   Creates  a  6LoWPAN	interface  named lowpan0 on the underlying IEEE
	   802.15.4 device wpan0.

       ip link add dev ip6erspan11 type ip6erspan seq key 102 local fc00:100::2
       remote fc00:100::1 erspan_ver 2 erspan_dir ingress erspan_hwid 17
	   Creates a IP6ERSPAN version 2 interface named ip6erspan00.

       ip link set dev swp0 type dsa conduit eth1
	   Changes the conduit interface of the swp0 user port to eth1.

SEE ALSO
       ip(8), ip-netns(8), ethtool(8), iptables(8)

AUTHOR
       Original Manpage by Michail Litvak <mci@owl.openwall.com>

iproute2			  13 Dec 2012			     IP-LINK(8)