search..
No manual entry for -- in section 8
troff:<standard input>:233: warning [p 3, 5.8i]: cannot break line
CRYPTSETUP-RESIZE(8)	      Maintenance Commands	   CRYPTSETUP-RESIZE(8)

NAME
       cryptsetup-resize - resize an active mapping

SYNOPSIS
       cryptsetup resize [<options>] <name>

DESCRIPTION
       Resizes an active mapping <name>.

       If --size (in 512-bytes sectors) or --device-size are not specified, the
       size is computed from the underlying device. For LUKS it is the size of
       the underlying device without the area reserved for LUKS header (see
       data payload offset in luksDump command). For plain crypt device, the
       whole device size is used.

       Note that this does not change the raw device geometry, it just changes
       how many sectors of the raw device are represented in the mapped device.

       If cryptsetup detected volume key for active device loaded in kernel
       keyring service, resize action would first try to retrieve the key using
       a token. Only if it failed, it'd ask for a passphrase to unlock a
       keyslot (LUKS) or to derive a volume key again (plain mode). The kernel
       keyring is used by default for LUKS2 devices.

       <options> can be [--size, --device-size, --token-id, --token-only,
       --token-type, --key-slot, --key-file, --keyfile-size, --keyfile-offset,
       --timeout, --disable-external-tokens, --disable-locks,
       --disable-keyring, --verify-passphrase, --timeout,
       --external-tokens-path].

OPTIONS
       --batch-mode, -q
	   Suppresses all confirmation questions. Use with care!

	   If the --verify-passphrase option is not specified, this option also
	   switches off the passphrase verification.

       --debug or --debug-json
	   Run in debug mode with full diagnostic logs. Debug output lines are
	   always prefixed by #.

	   If --debug-json is used, additional LUKS2 JSON data structures are
	   printed.

       --device-size size[units]
	   Sets new size of the device. If unset real device size is used.

	   If no unit suffix is specified, the size is in bytes.

	   Unit suffix can be S for 512 byte sectors, K/M/G/T (or
	   KiB,MiB,GiB,TiB) for units with 1024 base or KB/MB/GB/TB for 1000
	   base (SI scale).

       --disable-external-tokens
	   Disable loading of plugins for external LUKS2 tokens.

       --disable-keyring
	   Do not load volume key in kernel keyring and store it directly in
	   the dm-crypt target instead. This option is supported only for the
	   LUKS2 type.

       --disable-locks
	   Disable lock protection for metadata on disk. This option is valid
	   only for LUKS2 and ignored for other formats.

	   WARNING: Do not use this option unless you run cryptsetup in a
	   restricted environment where locking is impossible to perform (where
	   /run directory cannot be used).

       --external-tokens-path absolute_path
	   Override system directory path where cryptsetup searches for
	   external token handlers (or token plugins). It must be absolute path
	   (starting with '/' character).

       --header <device or file storing the LUKS header>
	   Use a detached (separated) metadata device or file where the LUKS
	   header is stored. This option allows one to store ciphertext and
	   LUKS header on different devices.

	   For commands that change the LUKS header (e.g. luksAddKey), specify
	   the device or file with the LUKS header directly as the LUKS device.

       --help, -?
	   Show help text and default parameters.

       --key-file, -d name
	   Read the passphrase from file.

	   If the name given is "-", then the passphrase will be read from
	   stdin. In this case, reading will not stop at newline characters.

	   See section NOTES ON PASSPHRASE PROCESSING in cryptsetup(8) for more
	   information.

       --keyfile-offset value
	   Skip value bytes at the beginning of the key file.

       --keyfile-size, -l value
	   Read a maximum of value bytes from the key file. The default is to
	   read the whole file up to the compiled-in maximum that can be
	   queried with --help. Supplying more data than the compiled-in
	   maximum aborts the operation.

	   This option is useful to cut trailing newlines, for example. If
	   --keyfile-offset is also given, the size count starts after the
	   offset.

       --key-slot, -S <0-N>
	   For LUKS operations that add key material, this option allows you to
	   specify which key slot is selected for the new key.

	   The maximum number of key slots depends on the LUKS version. LUKS1
	   can have up to 8 key slots. LUKS2 can have up to 32 key slots based
	   on key slot area size and key size, but a valid key slot ID can
	   always be between 0 and 31 for LUKS2.

       --size, -b <number of 512 byte sectors>
	   Set the size of the device in sectors of 512 bytes.

       --timeout, -t <number of seconds>
	   The number of seconds to wait before timeout on passphrase input via
	   terminal. It is relevant every time a passphrase is asked. It has no
	   effect if used in conjunction with --key-file.

	   This option is useful when the system should not stall if the user
	   does not input a passphrase, e.g. during boot. The default is a
	   value of 0 seconds, which means to wait forever.

       --token-id
	   Specify what token to use and allow token PIN prompt to take
	   precedence over interactive keyslot passphrase prompt. If omitted,
	   all available tokens (not protected by PIN) will be checked before
	   proceeding further with passphrase prompt.

       --token-only
	   Do not proceed further with action if token based keyslot unlock
	   failed. Without the option, action asks for passphrase to proceed
	   further.

	   It allows LUKS2 tokens protected by PIN to take precedence over
	   interactive keyslot passphrase prompt.

       --token-type type
	   Restrict tokens eligible for operation to specific token type.
	   Mostly useful when no --token-id is specified.

	   It allows LUKS2 type tokens protected by PIN to take precedence over
	   interactive keyslot passphrase prompt.

       --usage
	   Show short option help.

       --verify-passphrase, -y
	   When interactively asking for a passphrase, ask for it twice and
	   complain if both inputs do not match. Ignored on input from file or
	   stdin.

       --version, -V
	   Show the program version.

REPORTING BUGS
       Report bugs at cryptsetup mailing list <cryptsetup@lists.linux.dev> or
       in Issues project section
       <https://gitlab.com/cryptsetup/cryptsetup/-/issues/new>.

       Please attach output of the failed command with --debug option added.

SEE ALSO
       Cryptsetup FAQ
       <https://gitlab.com/cryptsetup/cryptsetup/wikis/FrequentlyAskedQuestions>

       cryptsetup(8), integritysetup(8) and veritysetup(8)

CRYPTSETUP
       Part of cryptsetup project <https://gitlab.com/cryptsetup/cryptsetup/>.

cryptsetup 2.7.5		   2025-05-04		   CRYPTSETUP-RESIZE(8)