search..
No manual entry for -- in section 8
troff:<standard input>:168: warning [p 2, 8.2i]: cannot break line
CRYPTSETUP-LUKSKILLSLOT(8)    Maintenance Commands   CRYPTSETUP-LUKSKILLSLOT(8)

NAME
       cryptsetup-luksKillSlot - wipe a key-slot from the LUKS device

SYNOPSIS
       cryptsetup luksKillSlot [<options>] <device> <key slot number>

DESCRIPTION
       Wipe the key-slot number <key slot> from the LUKS device. Except running
       in batch-mode (-q) a remaining passphrase must be supplied, either
       interactively or via --key-file. This command can remove the last
       remaining key-slot, but requires an interactive confirmation when doing
       so. Removing the last passphrase makes a LUKS container permanently
       inaccessible.

       <options> can be [--key-file, --keyfile-offset, --keyfile-size,
       --header, --disable-locks, --type, --verify-passphrase, --timeout].

       WARNING: If you read the passphrase from stdin (without further argument
       or with '-' as an argument to --key-file), batch-mode (-q) will be
       implicitly switched on and no warning will be given when you remove the
       last remaining passphrase from a LUKS container. Removing the last
       passphrase makes the LUKS container permanently inaccessible.

       NOTE: If there is no passphrase provided (on stdin or through --key-file
       argument) and batch-mode (-q) is active, the key-slot is removed without
       any other warning.

OPTIONS
       --batch-mode, -q
	   Suppresses all confirmation questions. Use with care!

	   If the --verify-passphrase option is not specified, this option also
	   switches off the passphrase verification.

       --debug or --debug-json
	   Run in debug mode with full diagnostic logs. Debug output lines are
	   always prefixed by #.

	   If --debug-json is used, additional LUKS2 JSON data structures are
	   printed.

       --disable-locks
	   Disable lock protection for metadata on disk. This option is valid
	   only for LUKS2 and ignored for other formats.

	   WARNING: Do not use this option unless you run cryptsetup in a
	   restricted environment where locking is impossible to perform (where
	   /run directory cannot be used).

       --header <device or file storing the LUKS header>
	   Use a detached (separated) metadata device or file where the LUKS
	   header is stored. This option allows one to store ciphertext and
	   LUKS header on different devices.

	   For commands that change the LUKS header (e.g. luksAddKey), specify
	   the device or file with the LUKS header directly as the LUKS device.

       --help, -?
	   Show help text and default parameters.

       --key-file, -d name
	   Read the passphrase from file.

	   If the name given is "-", then the passphrase will be read from
	   stdin. In this case, reading will not stop at newline characters.

	   See section NOTES ON PASSPHRASE PROCESSING in cryptsetup(8) for more
	   information.

       --keyfile-offset value
	   Skip value bytes at the beginning of the key file.

       --keyfile-size, -l value
	   Read a maximum of value bytes from the key file. The default is to
	   read the whole file up to the compiled-in maximum that can be
	   queried with --help. Supplying more data than the compiled-in
	   maximum aborts the operation.

	   This option is useful to cut trailing newlines, for example. If
	   --keyfile-offset is also given, the size count starts after the
	   offset.

       --timeout, -t <number of seconds>
	   The number of seconds to wait before timeout on passphrase input via
	   terminal. It is relevant every time a passphrase is asked. It has no
	   effect if used in conjunction with --key-file.

	   This option is useful when the system should not stall if the user
	   does not input a passphrase, e.g. during boot. The default is a
	   value of 0 seconds, which means to wait forever.

       --type <device-type>
	   Specifies required device type, for more info read BASIC ACTIONS
	   section in cryptsetup(8).

       --usage
	   Show short option help.

       --verify-passphrase, -y
	   When interactively asking for a passphrase, ask for it twice and
	   complain if both inputs do not match. Ignored on input from file or
	   stdin.

       --version, -V
	   Show the program version.

REPORTING BUGS
       Report bugs at cryptsetup mailing list <cryptsetup@lists.linux.dev> or
       in Issues project section
       <https://gitlab.com/cryptsetup/cryptsetup/-/issues/new>.

       Please attach output of the failed command with --debug option added.

SEE ALSO
       Cryptsetup FAQ
       <https://gitlab.com/cryptsetup/cryptsetup/wikis/FrequentlyAskedQuestions>

       cryptsetup(8), integritysetup(8) and veritysetup(8)

CRYPTSETUP
       Part of cryptsetup project <https://gitlab.com/cryptsetup/cryptsetup/>.

cryptsetup 2.7.5		   2025-05-04	     CRYPTSETUP-LUKSKILLSLOT(8)