search..
No manual entry for -- in section 8
RESIZE2FS(8)		    System Manager's Manual		   RESIZE2FS(8)

NAME
       resize2fs - ext2/ext3/ext4 file system resizer

SYNOPSIS
       resize2fs  [  -fFpPMbs  ]  [  -d	 debug-flags  ] [ -S RAID-stride ] [ -z
       undo_file ] device [ size ]

DESCRIPTION
       The resize2fs program will resize ext2, ext3, or ext4 file systems.   It
       can be used to enlarge or shrink an unmounted file system located on de-
       vice.   If the file system is mounted, it can be used to expand the size
       of the mounted file system, assuming the kernel and the file system sup-
       ports on-line resizing.	(Modern Linux 2.6 kernels will support	on-line
       resize  for  file systems mounted using ext3 and ext4; ext3 file systems
       will require the use of file systems with the resize_inode  feature  en-
       abled.)

       The  size parameter specifies the requested new size of the file system.
       If no units are specified, the units of the size parameter shall be  the
       file  system blocksize of the file system.  Optionally, the size parame-
       ter may be suffixed by one of the following units designators: 'K', 'M',
       'G', 'T' (either upper-case or lower-case) or 's' for power-of-two kilo-
       bytes, megabytes, gigabytes, terabytes or 512 byte sectors respectively.
       The size of the file system may never be larger than  the  size	of  the
       partition.   If	size parameter is not specified, it will default to the
       size of the partition.

       The resize2fs program does not manipulate the size  of  partitions.   If
       you wish to enlarge a file system, you must make sure you can expand the
       size of the underlying partition first.	This can be done using fdisk(8)
       by  deleting the partition and recreating it with a larger size or using
       lvextend(8), if you're using the logical volume	manager	 lvm(8).   When
       recreating the partition, make sure you create it with the same starting
       disk cylinder as before!	 Otherwise, the resize operation will certainly
       not  work,  and	you  may  lose	your entire file system.  After running
       fdisk(8), run resize2fs to resize the ext2 file system to use all of the
       space in the newly enlarged partition.

       If you wish to shrink an ext2 partition, first use resize2fs  to	 shrink
       the  size  of file system.  Then you may use fdisk(8) to shrink the size
       of the partition.  When shrinking the size of the partition,  make  sure
       you do not make it smaller than the new size of the ext2 file system!

       The  -b	and  -s	 options  enable and disable the 64bit feature, respec-
       tively.	The resize2fs program will, of course, take  care  of  resizing
       the block group descriptors and moving other data blocks out of the way,
       as needed.  It is not possible to resize the file system concurrent with
       changing the 64bit status.

OPTIONS
       -b     Turns on the 64bit feature, resizes the group descriptors as nec-
	      essary, and moves other metadata out of the way.

       -d debug-flags
	      Turns  on various resize2fs debugging features, if they have been
	      compiled into the binary.	  debug-flags  should  be  computed  by
	      adding  the  numbers  of	the desired features from the following
	      list:
		   2	- Debug block relocations
		   4	- Debug inode relocations
		   8	- Debug moving the inode table
		   16	- Print timing information
		   32	- Debug minimum file system size (-M) calculation

       -f     Forces resize2fs to proceed with the file	 system	 resize	 opera-
	      tion,  overriding some safety checks which resize2fs normally en-
	      forces.

       -F     Flush the file system device's buffer  caches  before  beginning.
	      Only really useful for doing resize2fs time trials.

       -M     Shrink  the file system to minimize its size as much as possible,
	      given the files stored in the file system.

       -p     Print out percentage completion bars  for	 each  resize2fs  phase
	      during  an  offline  (non-trivial)  resize operation, so that the
	      user can keep track of what the program is doing.	 (For very fast
	      resize operations, no progress bars may be displayed.)

       -P     Print an estimate of the number of file system blocks in the file
	      system if it is shrunk using resize2fs's -M option and then exit.

       -s     Turns off the 64bit feature and frees blocks that are  no	 longer
	      in use.

       -S RAID-stride
	      The  resize2fs  program  will  heuristically  determine  the RAID
	      stride that was specified when the file system was created.  This
	      option allows the user to explicitly specify a RAID  stride  set-
	      ting to be used by resize2fs instead.

       -z undo_file
	      Before overwriting a file system block, write the old contents of
	      the  block  to  an  undo	file.	This undo file can be used with
	      e2undo(8) to restore the old contents of the file	 system	 should
	      something	 go  wrong.   If  the  empty  string  is  passed as the
	      undo_file argument, the undo file will be written to a file named
	      resize2fs-device.e2undo  in  the	directory  specified  via   the
	      E2FSPROGS_UNDO_DIR environment variable.

	      WARNING:	The undo file cannot be used to recover from a power or
	      system crash.

KNOWN BUGS
       The minimum size of the file system as estimated by resize2fs may be in-
       correct, especially for file systems with 1k and 2k blocksizes.

AUTHOR
       resize2fs was written by Theodore Ts'o <tytso@mit.edu>.

COPYRIGHT
       Resize2fs is Copyright 1998 by Theodore Ts'o and PowerQuest,  Inc.   All
       rights reserved.	 As of April, 2000 Resize2fs may be redistributed under
       the terms of the GPL.

SEE ALSO
       fdisk(8), e2fsck(8), mke2fs(8), lvm(8), lvextend(8)

E2fsprogs version 1.47.2	  January 2025			   RESIZE2FS(8)