search..
No manual entry for -- in section 8
troff:<standard input>:302: warning [p 2, 2.7i]: cannot break line
ETHTOOL(8)		    System Manager's Manual		     ETHTOOL(8)

NAME
       ethtool - query or control network driver and hardware settings

SYNOPSIS

       ethtool devname

       ethtool -h|--help

       ethtool --version

       ethtool [--debug N] args

       ethtool [--disable-netlink] args

       ethtool [--json] args

       ethtool [-I | --include-statistics] args

       ethtool [--phy N] args

       ethtool --monitor [ command ] [ devname ]

       ethtool -a|--show-pause devname

       ethtool -A|--pause devname [autoneg on|off] [rx on|off] [tx on|off]

       ethtool -c|--show-coalesce devname

       ethtool -C|--coalesce devname [adaptive-rx on|off] [adaptive-tx on|off]
	      [rx-usecs N] [rx-frames N] [rx-usecs-irq N] [rx-frames-irq N]
	      [tx-usecs N] [tx-frames N] [tx-usecs-irq N] [tx-frames-irq N]
	      [stats-block-usecs N] [pkt-rate-low N] [rx-usecs-low N]
	      [rx-frames-low N] [tx-usecs-low N] [tx-frames-low N]
	      [pkt-rate-high N] [rx-usecs-high N] [rx-frames-high N]
	      [tx-usecs-high N] [tx-frames-high N] [sample-interval N]
	      [cqe-mode-rx on|off] [cqe-mode-tx on|off] [tx-aggr-max-bytes N]
	      [tx-aggr-max-frames N] [tx-aggr-time-usecs N]

       ethtool -g|--show-ring devname

       ethtool -G|--set-ring devname [rx N] [rx-mini N] [rx-jumbo N] [tx N]
	      [rx-buf-len N] [tcp-data-split auto|on|off] [cqe-size N]
	      [tx-push N] [rx-push N] [tx-push-buf-len N]

       ethtool -i|--driver devname

       ethtool -d|--register-dump devname [raw on|off] [hex on|off] [file name]

       ethtool -e|--eeprom-dump devname [raw on|off] [offset N] [length N]

       ethtool -E|--change-eeprom devname [magic N] [offset N] [length N]
	      [value N]

       ethtool -k|--show-features|--show-offload devname

       ethtool -K|--features|--offload devname feature on|off ...

       ethtool -p|--identify devname [N]

       ethtool -P|--show-permaddr devname

       ethtool -r|--negotiate devname

       ethtool -S|--statistics devname [--all-groups|--groups [eth-phy]
	      [eth-mac] [eth-ctrl] [rmon] ]

       ethtool --phy-statistics devname

       ethtool -t|--test devname [offline|online|external_lb]

       ethtool -s devname [speed N] [lanes N] [duplex half|full]
	      [port tp|aui|bnc|mii] [mdix auto|on|off] [autoneg on|off]
	      [advertise N[/M] | advertise mode on|off ...]  [phyad N]
	      [xcvr internal|external] [wol N[/M] | wol p|u|m|b|a|g|s|f|d...]
	      [sopass xx:yy:zz:aa:bb:cc] [master-slave preferred-
	      master|preferred-slave|forced-master|forced-slave] [msglvl
	      N[/M] | msglvl type on|off ...]

       ethtool -n|-u|--show-nfc|--show-ntuple devname
	      [ rx-flow-hash tcp4|udp4|ah4|esp4|sctp4|tcp6|udp6|ah6|esp6|sctp6 |
	      rule N ]

       ethtool -N|-U|--config-nfc|--config-ntuple devname
	      rx-flow-hash tcp4|udp4|ah4|esp4|sctp4|tcp6|udp6|ah6|esp6|sctp6
	      m|v|t|s|d|f|n|r... |
	      flow-type
	      ether|ip4|tcp4|udp4|sctp4|ah4|esp4|ip6|tcp6|udp6|ah6|esp6|sctp6
	      [src xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]]
	      [dst xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]] [proto N [m N]]
	      [src-ip ip-address [m ip-address]] [dst-ip ip-address [m ip-
	      address]] [tos N [m N]] [tclass N [m N]] [l4proto N [m N]]
	      [src-port N [m N]] [dst-port N [m N]] [spi N [m N]]
	      [l4data N [m N]] [vlan-etype N [m N]] [vlan N [m N]]
	      [user-def N [m N]] [dst-
	      mac xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]] [action N]
	      [context N] [loc N] |
	      delete N

       ethtool -w|--get-dump devname [data filename]

       ethtool -W|--set-dump devname N

       ethtool -T|--show-time-stamping devname [index N qualifier
	      precise|approx]

       ethtool --get-hwtimestamp-cfg devname

       ethtool --set-hwtimestamp-cfg devname [index N qualifier precise|approx]

       ethtool -x|--show-rxfh-indir|--show-rxfh devname

       ethtool -X|--set-rxfh-indir|--rxfh devname [hkey xx:yy:zz:aa:bb:cc:...]
	      [start N] [ equal N | weight W0 W1 ... | default ] [hfunc FUNC]
	      [xfrm symmetric-xor|none] [context CTX | new] [delete]

       ethtool -f|--flash devname file [N]

       ethtool -l|--show-channels devname

       ethtool -L|--set-channels devname [rx N] [tx N] [other N] [combined N]

       ethtool -m|--dump-module-eeprom|--module-info devname [raw on|off]
	      [hex on|off] [offset N] [length N] [page N] [bank N] [i2c N]

       ethtool --show-priv-flags devname

       ethtool --set-priv-flags devname flag on|off ...

       ethtool --show-eee devname

       ethtool --set-eee devname [eee on|off] [tx-lpi on|off] [tx-timer N]
	      [advertise N]

       ethtool --set-phy-tunable devname [ downshift on|off [count N] ] [
	      fast-link-down on|off [msecs N] ] [ energy-detect-power-down
	      on|off [msecs N] ]

       ethtool --get-phy-tunable devname [downshift] [fast-link-down] [energy-
	      detect-power-down]

       ethtool --get-tunable devname [rx-copybreak] [tx-copybreak] [tx-buf-
	      size] [pfc-prevention-tout]

       ethtool --set-tunable devname [rx-copybreak N] [tx-copybreak N]
	      [tx-buf-size N] [pfc-prevention-tout N]

       ethtool --reset devname [flags N] [mgmt] [mgmt-shared] [irq] [irq-
	      shared] [dma] [dma-shared] [filter] [filter-shared] [offload]
	      [offload-shared] [mac] [mac-shared] [phy] [phy-shared] [ram]
	      [ram-shared] [ap] [ap-shared] [dedicated] [all]

       ethtool --show-fec devname

       ethtool --set-fec devname encoding auto|off|rs|baser|llrs [...]

       ethtool -Q|--per-queue devname [queue_mask %x] sub_command ...

       ethtool --cable-test devname

       ethtool --cable-test-tdr devname [first N] [last N] [step N] [pair N]

       ethtool --show-tunnels devname

       ethtool --show-module devname

       ethtool --set-module devname [power-mode-policy high|auto]

       ethtool --get-plca-cfg devname

       ethtool --set-plca-cfg devname [enable on|off] [node-id N] [node-cnt N]
	      [to-tmr N] [burst-cnt N] [burst-tmr N]

       ethtool --get-plca-status devname

       ethtool --show-mm devname

       ethtool --set-mm devname [verify-enabled on|off] [verify-time N]
	      [tx-enabled on|off] [pmac-enabled on|off] [tx-min-frag-size N]

       ethtool --show-pse devname

       ethtool --set-pse devname [podl-pse-admin-control enable|disable]
	      [c33-pse-admin-control enable|disable] [c33-pse-avail-pw-limit N]

       ethtool --flash-module-firmware devname file FILE [pass PASS]

       ethtool --show-phys devname

DESCRIPTION
       ethtool	is used to query and control network device driver and hardware
       settings, particularly for wired Ethernet devices.

       devname is the name of the network device on which ethtool should  oper-
       ate.

OPTIONS
       ethtool with a single argument specifying the device name prints current
       settings of the specified device.

       -h --help
	      Shows a short help message.

       --version
	      Shows the ethtool version number.

       --debug N
	      Turns on debugging messages. Argument is interpreted as a mask:
	      0x01  Parser information
	      0x02  Summary of netlink messages
	      0x04  Hex dump of sent netlink messages
	      0x08  Hex dump of received netlink messages
	      0x10  Structure of netlink messages

       --disable-netlink
	      Do not use netlink and fall back to the ioctl interface if possi-
	      ble.

       --json Output  results in JavaScript Object Notation (JSON). Only a sub-
	      set of options support this. Those which do not will continue  to
	      output plain text in the presence of this option.

       -I --include-statistics
	      Include command-related statistics in the output. This op<standard input>:878: warning: table wider than line length minus indentation
<standard input>:903: warning: table wider than line length minus indentation
tion al-
	      lows  displaying relevant device statistics for selected get com-
	      mands.

       --phy N
	      Target a PHY within the interface. The PHY index can be retrieved
	      with --show-phys. PHY index 0 targets the phy device directly at-
	      tached to the ethernet MAC, if any.  The following  commands  can
	      accept a PHY index:
	      --cable-test
	      --cable-test-tdr
	      --get-plca-cfg
	      --set-plca-cfg
	      --get-plca-status
	      --show-pse
	      --set-pse

       -a --show-pause
	      Queries  the specified Ethernet device for pause parameter infor-
	      mation.

	   --src aggregate|emac|pmac
		  If the MAC Merge layer is  supported,	 request  a  particular
		  source  of  device  statistics (eMAC or pMAC, or their aggre-
		  gate). Only valid if ethtool was invoked with	 the  -I  --in-
		  clude-statistics argument.

       -A --pause
	      Changes the pause parameters of the specified Ethernet device.

	   autoneg on|off
		  Specifies whether pause autonegotiation should be enabled.

	   rx on|off
		  Specifies whether RX pause should be enabled.

	   tx on|off
		  Specifies whether TX pause should be enabled.

       -c --show-coalesce
	      Queries the specified network device for coalescing information.

       -C --coalesce
	      Changes the coalescing settings of the specified network device.

       -g --show-ring
	      Queries the specified network device for rx/tx ring parameter in-
	      formation.

       -G --set-ring
	      Changes  the  rx/tx  ring parameters of the specified network de-
	      vice.

	   rx N	  Changes the number of ring entries for the Rx ring.

	   rx-mini N
		  Changes the number of ring entries for the Rx Mini ring.

	   rx-jumbo N
		  Changes the number of ring entries for the Rx Jumbo ring.

	   tx N	  Changes the number of ring entries for the Tx ring.

	   rx-buf-len N
		  Changes the size of a buffer in the Rx ring.

	   tcp-data-split auto|on|off
		  Specifies the state of TCP data split.

	   cqe-size N
		  Changes the size of completion queue event.

	   tx-push on|off
		  Specifies whether TX push should be enabled.

	   rx-push on|off
		  Specifies whether RX push should be enabled.

	   tx-push-buf-len N
		  Specifies the maximum number of bytes of a transmitted packet
		  a driver can push directly to the underlying device

       -i --driver
	      Queries the specified network device for associated driver infor-
	      mation.

       -d --register-dump
	      Retrieves and prints a register dump for	the  specified	network
	      device.  The register format for some devices is known and decod-
	      ed  others are printed in hex.  When raw is enabled, then ethtool
	      dumps the raw register data to stdout.   If  file	 is  specified,
	      then  use	 contents  of  previous	 raw register dump, rather than
	      reading from the device.

       -e --eeprom-dump
	      Retrieves and prints an EEPROM dump for the specified network de-
	      vice.  When raw is enabled, then it dumps the raw EEPROM data  to
	      stdout.  The  length  and offset parameters allow dumping certain
	      portions of the EEPROM.  Default is to dump the entire EEPROM.

	   raw on|off

	   offset N

	   length N

       -E --change-eeprom
	      If value is specified, changes EEPROM byte for the specified net-
	      work device.  offset and value specify which byte	 and  it's  new
	      value.  If  value	 is not specified, stdin is read and written to
	      the EEPROM. The length and offset	 parameters  allow  writing  to
	      certain portions of the EEPROM.  Because of the persistent nature
	      of  writing  to  the  EEPROM, a device-specific magic key must be
	      specified to prevent the accidental writing to the EEPROM.

       -k --show-features --show-offload
	      Queries the specified network device for the  state  of  protocol
	      offload and other features.

       -K --features --offload
	      Changes  the  offload parameters and other features of the speci-
	      fied network device.  The following feature  names  are  built-in
	      and others may be defined by the kernel.

	   rx on|off
		  Specifies whether RX checksumming should be enabled.

	   tx on|off
		  Specifies whether TX checksumming should be enabled.

	   sg on|off
		  Specifies whether scatter-gather should be enabled.

	   tso on|off
		  Specifies whether TCP segmentation offload should be enabled.

	   ufo on|off
		  Specifies whether UDP fragmentation offload should be enabled

	   gso on|off
		  Specifies  whether generic segmentation offload should be en-
		  abled

	   gro on|off
		  Specifies whether generic receive offload should be enabled

	   lro on|off
		  Specifies whether large receive offload should be enabled

	   rxvlan on|off
		  Specifies whether RX VLAN acceleration should be enabled

	   txvlan on|off
		  Specifies whether TX VLAN acceleration should be enabled

	   ntuple on|off
		  Specifies whether Rx ntuple filters and actions should be en-
		  abled

	   rxhash on|off
		  Specifies whether receive hashing offload should be enabled

       -p --identify
	      Initiates adapter-specific action intended to enable an  operator
	      to easily identify the adapter by sight.	Typically this involves
	      blinking one or more LEDs on the specific network port.

	   [ N]	  Length of time to perform phys-id, in seconds.

       -P --show-permaddr
	      Queries  the  specified network device for permanent hardware ad-
	      dress.

       -r --negotiate
	      Restarts auto-negotiation on the specified  Ethernet  device,  if
	      auto-negotiation is enabled.

       -S --statistics
	      Queries  the  specified  network device for standard (IEEE, IETF,
	      etc.), or NIC- and driver-specific statistics. NIC-  and	driver-
	      specific	statistics are requested when no group of statistics is
	      specified.

	      NIC- and driver-specific statistics and standard	statistics  are
	      independent, devices may implement either, both or none. There is
	      little  commonality  between  naming  of NIC- and driver-specific
	      statistics across vendors.

	   --all-groups

	   --groups [eth-phy] [eth-mac] [eth-ctrl] [rmon]
		  Request groups of standard device statistics.

	   --src aggregate|emac|pmac
		  If the MAC Merge layer is  supported,	 request  a  particular
		  source  of  device  statistics (eMAC or pMAC, or their aggre-
		  gate).

       --phy-statistics
	      Queries the specified network device for PHY specific statistics.

       -t --test
	      Executes adapter selftest on the specified network device. Possi-
	      ble test modes are:

	   offline
		  Perform full set of tests, possibly interrupting normal oper-
		  ation during the tests,

	   online Perform limited set of tests, not interrupting normal	 opera-
		  tion,

	   external_lb
		  Perform  full	 set of tests, as for offline, and addition<standard input>:1095: warning: table wider than line length minus indentation
ally
		  an external-loopback test.

       -s --change
	      Allows changing some or all settings of the specified network de-
	      vice.  All following options only apply if -s was specified.

	   speed N
		  Set speed in Mb/s.  ethtool with just the device name	 as  an
		  argument will show you the supported device speeds.

	   lanes N
		  Set number of lanes.

	   duplex half|full
		  Sets full or half duplex mode.

	   port tp|aui|bnc|mii
		  Selects device port.

	   master-slave preferred-master|preferred-slave|forced-master|forced-
	   slave
		  Configure  MASTER/SLAVE role of the PHY. When the PHY is con-
		  figured as MASTER, the PMA  Transmit	function  shall	 source
		  TX_TCLK  from a local clock source. When configured as SLAVE,
		  the PMA Transmit function shall source TX_TCLK from the clock
		  recovered from data stream provided by MASTER.  Not  all  de-
		  vices support this.
		  preferred-master   Prefer MASTER role on autonegotiation
		  preferred-slave    Prefer SLAVE role on autonegotiation
		  forced-master	     Force the PHY in MASTER role. Can be used without autonegotiation
		  forced-slave	     Force the PHY in SLAVE role. Can be used without autonegotiation

	   mdix auto|on|off
		  Selects  MDI-X mode for port. May be used to override the au-
		  tomatic detection feature of most adapters.  An  argument  of
		  auto means automatic detection of MDI status, on forces MDI-X
		  (crossover)  mode,  while  off  means	 MDI (straight through)
		  mode.	 The driver should guarantee that  this	 command  takes
		  effect  immediately,	and  if necessary may reset the link to
		  cause the change to take effect.

	   autoneg on|off
		  Specifies whether autonegotiation should be enabled.	Autone-
		  gotiation  is enabled by default, but in some network devices
		  may have trouble with it, so you can	disable	 it  if	 really
		  necessary.

	   advertise N
		  Sets the speed and duplex advertised by autonegotiation.  The
		  argument is a hexadecimal value using one or a combination of
		  the following values:
		  0x001				 10baseT Half
		  0x002				 10baseT Full
		  0x100000000000000000000000	 10baseT1L Full
		  0x8000000000000000000000000	 10baseT1S Full
		  0x10000000000000000000000000	 10baseT1S Half
		  0x20000000000000000000000000	 10baseT1S_P2MP Half
		  0x40000000000000000000000000	 10baseT1BRR Full
		  0x004				 100baseT Half
		  0x008				 100baseT Full
		  0x80000000000000000		 100baseT1 Full
		  0x40000000000000000000000	 100baseFX Half
		  0x80000000000000000000000	 100baseFX Full
		  0x010				 1000baseT Half		      (not supported by IEEE standards)
		  0x020				 1000baseT Full
		  0x20000			 1000baseKX Full
		  0x20000000000			 1000baseX Full
		  0x100000000000000000		 1000baseT1 Full
		  0x8000			 2500baseX Full		      (not supported by IEEE standards)
		  0x800000000000		 2500baseT Full
		  0x1000000000000		 5000baseT Full
		  0x1000			 10000baseT Full
		  0x40000			 10000baseKX4 Full
		  0x80000			 10000baseKR Full
		  0x100000			 10000baseR_FEC
		  0x40000000000			 10000baseCR Full
		  0x80000000000			 10000baseSR Full
		  0x100000000000		 10000baseLR Full
		  0x200000000000		 10000baseLRM Full
		  0x400000000000		 10000baseER Full
		  0x200000			 20000baseMLD2 Full	      (not supported by IEEE standards)
		  0x400000			 20000baseKR2 Full	      (not supported by IEEE standards)
		  0x80000000			 25000baseCR Full
		  0x100000000			 25000baseKR Full
		  0x200000000			 25000baseSR Full
		  0x800000			 40000baseKR4 Full
		  0x1000000			 40000baseCR4 Full
		  0x2000000			 40000baseSR4 Full
		  0x4000000			 40000baseLR4 Full
		  0x400000000			 50000baseCR2 Full
		  0x800000000			 50000baseKR2 Full
		  0x10000000000			 50000baseSR2 Full
		  0x10000000000000		 50000baseKR Full
		  0x20000000000000		 50000baseSR Full
		  0x40000000000000		 50000baseCR Full
		  0x80000000000000		 50000baseLR_ER_FR Full
		  0x100000000000000		 50000baseDR Full
		  0x8000000			 56000baseKR4 Full
		  0x10000000			 56000baseCR4 Full
		  0x20000000			 56000baseSR4 Full
		  0x40000000			 56000baseLR4 Full
		  0x1000000000			 100000baseKR4 Full
		  0x2000000000			 100000baseSR4 Full
		  0x4000000000			 100000baseCR4 Full
		  0x8000000000			 100000baseLR4_ER4 Full
		  0x200000000000000		 100000baseKR2 Full
		  0x400000000000000		 100000baseSR2 Full
		  0x800000000000000		 100000baseCR2 Full
		  0x1000000000000000		 100000baseLR2_ER2_FR2 Full
		  0x2000000000000000		 100000baseDR2 Full
		  0x8000000000000000000		 100000baseKR Full
		  0x10000000000000000000	 100000baseSR Full
		  0x20000000000000000000	 100000baseLR_ER_FR Full
		  0x40000000000000000000	 100000baseCR Full
		  0x80000000000000000000	 100000baseDR Full
		  0x4000000000000000		 200000baseKR4 Full
		  0x8000000000000000		 200000baseSR4 Full
		  0x10000000000000000		 200000baseLR4_ER4_FR4 Full
		  0x20000000000000000		 200000baseDR4 Full
		  0x40000000000000000		 200000baseCR4 Full
		  0x100000000000000000000	 200000baseKR2 Full
		  0x200000000000000000000	 200000baseSR2 Full
		  0x400000000000000000000	 200000baseLR2_ER2_FR2 Full
		  0x800000000000000000000	 200000baseDR2 Full
		  0x1000000000000000000000	 200000baseCR2 Full
		  0x200000000000000000		 400000baseKR8 Full
		  0x400000000000000000		 400000baseSR8 Full
		  0x800000000000000000		 400000baseLR8_ER8_FR8 Full
		  0x1000000000000000000		 400000baseDR8 Full
		  0x2000000000000000000		 400000baseCR8 Full
		  0x2000000000000000000000	 400000baseKR4 Full
		  0x4000000000000000000000	 400000baseSR4 Full
		  0x8000000000000000000000	 400000baseLR4_ER4_FR4 Full
		  0x10000000000000000000000	 400000baseDR4 Full
		  0x20000000000000000000000	 400000baseCR4 Full
		  0x200000000000000000000000	 800000baseCR8 Full
		  0x400000000000000000000000	 800000baseKR8 Full
		  0x800000000000000000000000	 800000baseDR8 Full
		  0x1000000000000000000000000	 800000baseDR8_2 Full
		  0x2000000000000000000000000	 800000baseSR8 Full
		  0x4000000000000000000000000	 800000baseVR8 Full

	   phyad N
		  PHY address.

	   xcvr internal|external
		  Selects  transceiver type. Currently only internal and exter-
		  nal can be specified, in the future further  types  might  be
		  added.

	   wol p|u|m|b|a|g|s|f|d...
		  Sets Wake-on-LAN options.  Not all devices support this.  The
		  argument  to this option is a string of characters specifying
		  which options to enable.
		  p   Wake on PHY activity
		  u   Wake on unicast messages
		  m   Wake on multicast messages
		  b   Wake on broadcast messages
		  a   Wake on ARP
		  g   Wake on MagicPackettm
		  s   Enable SecureOntm password for MagicPackettm
		  f   Wake on filter(s)
		  d   Disable  (wake  on  nothing).   This  option
		      clears all previous options.

	   sopass xx:yy:zz:aa:bb:cc
		  Sets	the  SecureOntm	 password.  The argument to this option
		  must	 be   6	  bytes	  in   Ethernet	   MAC	  hex	 format
		  (xx:yy:zz:aa:bb:cc).

	   msglvl N
	   msglvl type on|off ...
		  Sets	the  driver  message type flags by name or number. type
		  names the type of message to enable or disable;  N  specifies
		  the new flags numerically. The defined type names and numbers
		  are:
		  drv	      0x0001  General driver status
		  probe	      0x0002  Hardware probing
		  link	      0x0004  Link state
		  timer	      0x0008  Periodic status check
		  ifdown      0x0010  Interface being brought down
		  ifup	      0x0020  Interface being brought up
		  rx_err      0x0040  Receive error
		  tx_err      0x0080  Transmit error
		  tx_queued   0x0100  Transmit queueing
		  intr	      0x0200  Interrupt handling
		  tx_done     0x0400  Transmit completion
		  rx_status   0x0800  Receive completion
		  pktdata     0x1000  Packet contents
		  hw	      0x2000  Hardware status
		  wol	      0x4000  Wake-on-LAN status

		  The  precise meanings of these type flags differ between dri-
		  vers.

       -n -u --show-nfc --show-ntuple
	      Retrieves receive network flow classification options or rules.

	   rx-flow-hash tcp4|udp4|ah4|esp4|sctp4|tcp6|udp6|ah6|esp6|sctp6
		  Retrieves the hash options for the specified flow type.
		  tcp4	  TCP over IPv4
		  udp4	  UDP over IPv4
		  ah4	  IPSEC AH over IPv4
		  esp4	  IPSEC ESP over IPv4
		  sctp4	  SCTP over IPv4
		  tcp6	  TCP over IPv6
		  udp6	  UDP over IPv6
		  ah6	  IPSEC AH over IPv6
		  esp6	  IPSEC ESP over IPv6
		  sctp6	  SCTP over IPv6

	   rule N Retrieves the RX classification rule with the given ID.

       -N -U --config-nfc --config-ntuple
	      Configures receive network flow classification options or rules.

	   rx-flow-hash tcp4|udp4|ah4|esp4|sctp4|tcp6|udp6|ah6|esp6|sctp6
     <standard input>:1451: warning: table wider than line length minus indentation
<standard input>:1465: warning: table wider than line length minus indentation
      m|v|t|s|d|f|n|r...
		  Configures the hash options for the specified flow type.
		  m   Hash on the Layer 2 destination address of the rx packet.
		  v   Hash on the VLAN tag of the rx packet.
		  t   Hash on the Layer 3 protocol field of the rx packet.
		  s   Hash on the IP source address of the rx packet.
		  d   Hash on the IP destination address of the rx packet.
		  f   Hash on bytes 0 and 1 of the Layer 4 header of the rx packet.
		  n   Hash on bytes 2 and 3 of the Layer 4 header of the rx packet.
		  r   Discard all packets of this flow type. When  this	 option	 is
		      set, all other options are ignored.

	   flow-type
	   ether|ip4|tcp4|udp4|sctp4|ah4|esp4|ip6|tcp6|udp6|ah6|esp6|sctp6
		  Inserts  or  updates	a classification rule for the specified
		  flow type.
		  ether	  Ethernet
		  ip4	  Raw IPv4
		  tcp4	  TCP over IPv4
		  udp4	  UDP over IPv4
		  sctp4	  SCTP over IPv4
		  ah4	  IPSEC AH over IPv4
		  esp4	  IPSEC ESP over IPv4
		  ip6	  Raw IPv6
		  tcp6	  TCP over IPv6
		  udp6	  UDP over IPv6
		  sctp6	  SCTP over IPv6
		  ah6	  IPSEC AH over IPv6
		  esp6	  IPSEC ESP over IPv6

	   For all fields that allow both a value and a mask to	 be  specified,
	   the	mask  may  be specified immediately after the value using the m
	   keyword, or separately using the field name keyword with  -mask  ap-
	   pended, e.g. src-mask.

	   src xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]
		  Includes  the	 source	 MAC  address,	specified as 6 bytes in
		  hexadecimal separated by colons, along with an optional mask.
		  Valid only for flow-type ether.

	   dst xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]
		  Includes the destination MAC address, specified as 6 bytes in
		  hexadecimal separated by colons, along with an optional mask.
		  Valid only for flow-type ether.

	   proto N [m N]
		  Includes the Ethernet protocol number (ethertype) and an  op-
		  tional mask.	Valid only for flow-type ether.

	   src-ip ip-address [m ip-address]
		  Specify the source IP address of the incoming packet to match
		  along	 with  an  optional mask.  Valid for all IP based flow-
		  types.

	   dst-ip ip-address [m ip-address]
		  Specify the destination IP address of the incoming packet  to
		  match	 along	with  an optional mask.	 Valid for all IP based
		  flow-types.

	   tos N [m N]
		  Specify the value of the Type of Service field in the	 incom-
		  ing  packet to match along with an optional mask.  Applies to
		  all IPv4 based flow-types.

	   tclass N [m N]
		  Specify the value of the Traffic Class field in the  incoming
		  packet  to match along with an optional mask.	 Applies to all
		  IPv6 based flow-types.

	   l4proto N [m N]
		  Includes the layer  4	 protocol  number  and	optional  mask.
		  Valid only for flow-types ip4 and ip6.

	   src-port N [m N]
		  Specify  the	value  of  the source port field (applicable to
		  TCP/UDP packets) in the incoming packet to match  along  with
		  an  optional mask.  Valid for flow-types ip4, tcp4, udp4, and
		  sctp4 and their IPv6 equivalents.

	   dst-port N [m N]
		  Specify the value of the destination port  field  (applicable
		  to TCP/UDP packets)in the incoming packet to match along with
		  an  optional mask.  Valid for flow-types ip4, tcp4, udp4, and
		  sctp4 and their IPv6 equivalents.

	   spi N [m N]
		  Specify the value of the security parameter index field  (ap-
		  plicable  to	AH/ESP	packets)in the incoming packet to match
		  along with an optional mask.	Valid for flow-types ip4,  ah4,
		  and esp4 and their IPv6 equivalents.

	   l4data N [m N]
		  Specify  the value of the first 4 Bytes of Layer 4 in the in-
		  coming packet to match along with an	optional  mask.	  Valid
		  for ip4 and ip6 flow-types.

	   vlan-etype N [m N]
		  Includes the VLAN tag Ethertype and an optional mask.

	   vlan N [m N]
		  Includes the VLAN tag and an optional mask.

	   user-def N [m N]
		  Includes 64-bits of user-specific data and an optional mask.

	   dst-mac xx:yy:zz:aa:bb:cc [m xx:yy:zz:aa:bb:cc]
		  Includes the destination MAC address, specified as 6 bytes in
		  hexadecimal separated by colons, along with an optional mask.
		  Valid for all IP based flow-types.

	   action N
		  Specifies  the Rx queue to send packets to, or some other ac-
		  tion.
		  -1		Drop the matched flow
		  -2		Use the matched flow as a Wake-on-LAN filter
		  0 or higher	Rx queue to route the flow

	   context N
		  Specifies the RSS context to	spread	packets	 over  multiple
		  queues;  either 0 for the default RSS context, or a value re-
		  turned by ethtool -X ... context new.	 If combined  with  ac-
		  tion or queue,  the  Rx  queue specified will be added to the
		  value read from the RSS indirection table to produce the  ac-
		  tual Rx queue to deliver to.

	   vf N	  Specifies  the  Virtual  Function  the filter applies to. Not
		  compatible with action.

	   queue N
		  Specifies the Rx queue to send  packets  to.	Not  compatible
		  with action.

	   loc N  Specify  the	location/ID to insert the rule. This will over-
		  write any rule present in  that  location  and  will	not  go
		  through any of the rule ordering process.

	   delete N
		  Deletes the RX classification rule with the given ID.

       -w --get-dump
	      Retrieves	 and prints firmware dump for the specified network de-
	      vice.  By default, it prints  out	 the  dump  flag,  version  and
	      length  of  the  dump data.  When data is indicated, then ethtool
	      fetches the dump data and directs it to a file.

       -W --set-dump
	      Sets the dump flag for the device.

       -T --show-time-stamping
	      Show the device's time stamping capabilities and	associated  PTP
	      hardware	clock.	Show the capabilities of the currently selected
	      time stamping if no index and qualifier is provided.

	   index N
		  Index of the ptp hardware clock

	   qualifier precise|approx
		  Qualifier of the ptp hardware clock. Mainly "precise" the de-
		  fault one is for IEEE 1588 quality and "approx" is  for  NICs
		  DMA point.

       --get-hwtimestamp-cfg
	      Show the selected time stamping PTP hardware clock configuration.

       --set-hwtimestamp-cfg
	      Select the device's time stamping PTP hardware clock.

	   index N
		  Index of the ptp hardware clock

	   qualifier precise|approx
		  Qualifier of the ptp hardware clock. Mainly "precise" the de-
		  fault	 one  is for IEEE 1588 quality and "approx" is for NICs
		  DMA point.

       -x --show-rxfh-indir --show-rxfh
	      Retrieves the receive flow hash indirection table and/or RSS hash
	      key.

       -X --set-rxfh-indir --rxfh
	      Configures the receive flow hash	indirection  table  and/or  RSS
	      hash key.

	   hkey	  Sets	RSS  hash key of the specified network device. RSS hash
		  key should be of device supported length.   Hash  key	 format
		  must	be in xx:yy:zz:aa:bb:cc format meaning both the nibbles
		  of a byte should be mentioned even if a nibble is zero.

	   hfunc  Sets RSS hash function of the specified network device.  List
		  of RSS hash functions which kernel supports  is  shown  as  a
		  part of the --show-rxfh command output.

	   xfrm	  Sets	the  RSS input transformation. Currently, only the sym-
		  metric-xor transformation is supported where the NIC XORs the
		  L3 and/or L4 source and destination fields  (as  selected  by
		  --config-nfc	rx-flow-hash  ) before passing them to the hash
		  algorithm. The RSS hash function will	 then  yield  the  same
		  hash for the other flow direction where the source and desti-
		  nation  fields  are  swapped	(i.e. Symmetric RSS). Note that
		  XORing the input parameters reduces the entropy of the  input
		  set  and  the	 hash algorithm could potentially be exploited.
		  Switch off (default) by xfrm none.

	   start N
		  For the equal and weight options, sets the  starting	receive
		  queue for spreading flows to N.

	   equal N
		  Sets	the receive flow hash indirection table to spread flows
		  evenly between the first N receive queues.

	   weight W0 W1 ...
		  Sets the receive flow hash indirection table to spread  flows
		  between  receive  queues according to the given weights.  The
		  sum of the weights must be non-zero and must not  exceed  the
		  size of the indirection table.

	   default
		  Sets	the  receive flow hash indirection table to its default
		  value.

	   context CTX | new
		  Specifies an RSS context to act on; either new to allocate  a
		  new  RSS  context,  or  CTX,	a  value returned by a previous
		  ... context new.

	   delete Delete the specified RSS context.  May only be used  in  con-
		  junction with context and a non-zero CTX value.

       -f --flash
	      Write  a	firmware image to flash or other non-volatile memory on
	      the device.

	   file	  Specifies the filename of the firmware image.	  The  firmware
		  must	first  be installed in one of the directories where the
		  kernel firmware loader or firmware agent will look,  such  as
		  /lib/firmware.

	   N	  If the device stores multiple firmware images in separate re-
		  gions	 of  non-volatile memory, this parameter may be used to
		  specify which region is to be written.  The default is 0, re-
		  questing that all regions are written.  All other values  are
		  driver-dependent.

       -l --show-channels
	      Queries  the specified network device for the numbers of channels
	      it has.  A channel is an IRQ and the set of queues that can trig-
	      ger that IRQ.

       -L --set-channels
	      Changes the numbers of channels of the specified network device.

	   rx N	  Changes the number of channels with only receive queues.

	   tx N	  Changes the number of channels with only transmit queues.

	   other N
		  Changes the number of channels used only for	other  purposes
		  e.g. link interrupts or SR-IOV co-ordination.

	   combined N
		  Changes the number of multi-purpose channels.

       -m --dump-module-eeprom --module-info
	      Retrieves and if possible decodes the EEPROM from plugin modules,
	      e.g SFP+, QSFP.  If the driver and module support it, the optical
	      diagnostic information is also read and decoded.	When either one
	      of  page,	 bank  or  i2c parameters is specified, dumps only of a
	      single page or its portion is allowed. In such a case offset  and
	      length  parameters  are  treated relatively to EEPROM page bound-
	      aries.

       --show-priv-flags
	      Queries the specified network device for its private flags.   The
	      names  and meanings of private flags (if any) are defined by each
	      network device driver.

       --set-priv-flags
	      Sets the device's private flags as specified.

	   flag on|off Sets the state of the named private flag.

       --show-eee
	      Queries the specified network device for its support  of	Energy-
	      Efficient Ethernet (according to the IEEE 802.3az specifications)

       --set-eee
	      Sets the device EEE behaviour.

	   eee on|off
		  Enables/disables the device support of EEE.

	   tx-lpi on|off
		  Determines whether the device should assert its Tx LPI.

	   advertise N
		  Sets the speeds for which the device should advertise EEE ca-
		  pabilities.  Values are as for --change advertise

	   tx-timer N
		  Sets	the  amount of time the device should stay in idle mode
		  prior to asserting its Tx LPI	 (in  microseconds).  This  has
		  meaning only when Tx LPI is enabled.

       --set-phy-tunable
	      Sets the PHY tunable parameters.

	   downshift on|off
		  Specifies whether downshift should be enabled.
		  count N
		      Sets the PHY downshift re-tries count.

	   fast-link-down on|off
		  Specifies  whether  Fast Link Down should be enabled and time
		  until link down (if supported).
		  msecs N
		      Sets the period after which the link is reported as down. Note that the PHY may choose
		      the closest supported value. Only on reading back the tunable do you get the actual value.

	   energy-detect-power-down on|off
		  Specifies whether Energy Detect Power Down (EDPD)  should  be
		  enabled  (if supported).  This will put the RX and TX circuit
		  blocks into a low power mode, and the PHY will wake up  peri-
		  odically  to	send link pulses to avoid any lock-up situation
		  with a peer PHY that may also have EDPD enabled. By  default,
		  this setting will also enable the periodic transmission of TX
		  pulses.
		  msecs N
		      Some PHYs support configuration of the wake-up interval to send TX pulses.
		      This setting allows the control of this interval, and 0 disables TX pulses
		      if the PHY supports this. Disabling TX pulses can create a lock-up situation
		      where neither of the PHYs wakes the other one. If unspecified the default
		      value (in milliseconds) will be used by the PHY.

       --get-phy-tunable
	      Gets the PHY tunable parameters.

	   downshift
		  For  operation  in cabling environments that are incompatible
		  with 1000BASE-T, PHY device provides an automatic link  speed
		  downshift  operation.	  Link	speed  downshift after N failed
		  1000BASE-T auto-negotiation attempts.	  Downshift  is	 useful
		  where cable does not have the 4 pairs instance.

		  Gets the PHY downshift count/status.

	   fast-link-down
		  Depending  on	 the  mode it may take 0.5s - 1s until a broken
		  link is reported as down.  In certain use cases  a  link-down
		  event	 needs	to  be reported as soon as possible.  Some PHYs
		  support a Fast Link Down Feature and may allow  configuration
		  of the delay before a broken link is reported as being down.

		  Gets the PHY Fast Link Down status / period.

	   energy-detect-power-down
		  Gets	the  current configured setting for Energy Detect Power
		  Down (if supported).

       --get-tunable
	      Get the tunable parameters.

	   rx-copybreak
		  Get the current rx copybreak value in bytes.

	   tx-copybreak
		  Get the current tx copybreak value in bytes.

	   tx-buf-size
		  Get the current tx copybreak buffer size in bytes.

	   pfc-prevention-tout
		  Get the current pfc prevention timeout value in msecs.

       --set-tunable
	      Set driver's tunable parameters.

	   rx-copybreak N
		  Set the rx copybreak value in bytes.

	   tx-copybreak N
		  Set the tx copybreak value in bytes.

	   tx-buf-size N
		  Set the tx copybreak buffer size in bytes.

	   pfc-prevention-tout N
		  Set pfc prevention timeout in msecs. Value of 0 means disable
		  and 65535 means auto.

       --reset
	      Reset hardware components specified by flags and components list-
	      ed below

	   flags N
		  Resets the components based on direct flags mask

	   mgmt	  Management processor

	   irq	  Interrupt requester

	   dma	  DMA engine

	   filter Filtering/flow direction

	   offload
		  Protocol offload

	   mac	  Media access controller

	   phy	  Transceiver/PHY

	   ram	  RAM shared between multiple components ap Application Proces-
		  sor

	   dedicated
		  All components dedicated to this interface

	   all	  All components used by this interface, even if shared

       --show-fec
	      Queries the specified network device for its support  of	Forward
	      Error Correction.

       --set-fec
	      Configures Forward Error Correction for the specified network de-
	      vice.

	      Forward Error Correction modes selected by a user are expected to
	      be  persisted  after  any	 hotplug events. If a module is swapped
	      that does not  support  the  current  FEC	 mode,	the  driver  or
	      firmware	must take the link down administratively and report the
	      problem in the system logs for users to correct.

	   encoding auto|off|rs|baser|llrs [...]

		  Sets the FEC encoding for the device.	  Combinations	of  op-
		  tions are specified as e.g.  encoding auto rs ; the semantics
		  of such combinations vary between drivers.
		  auto	  Use the driver's default encoding
		  off	  Turn off FEC
		  RS	  Force RS-FEC encoding
		  BaseR	  Force BaseR encoding
		  LLRS	  Force LLRS-FEC encoding

       -Q|--per-queue
	      Applies provided sub command to specific queues.

	   queue_mask %x
		  Sets the specific queues which the sub command is applied to.
		  If  queue_mask is not set, the sub command will be applied to
		  all queues.

	   sub_command
		  Sub command to apply.	 The  supported	 sub  commands	include
		  --show-coalesce and --coalesce.

       --cable-test
	      Perform a cable test and report the results. What results are re-
	      turned depends on the capabilities of the network interface. Typ-
	      ically  open  pairs and shorted pairs can be reported, along with
	      pairs being O.K. When a fault is detected	 the  approximate  dis-
	      tance to the fault may be reported.

       --cable-test-tdr
	      Perform a cable test and report the raw Time Domain Reflectometer
	      data.  A pulse is sent down a cable pair and the amplitude of the
	      reflection, for a given distance, is reported. A break in the ca-
	      ble returns a big reflection. Minor damage to the cable returns a
	      small  reflection.  If the cable is shorted, the amplitude of the
	      reflection can be negative. By  default,	data  is  returned  for
	      lengths  between	0  and 150m at 1m steps, for all pairs. However
	      parameters can be passed to restrict the collection of  data.  It
	      should  be  noted, that the interface will round the distances to
	      whatever granularity is actually implemented. This is  often  0.8
	      of  a  meter. The results should include the actual rounded first
	      and last distance and step size.

	   first  N
		  Distance along the cable, in meters, where the first measure-
		  ment should be made.

	   last	 N
		  Distance along the cable, in meters, where the last  measure-
		  ment should be made.

	   step	 N
		  Distance, in meters, between each measurement.

	   pair	 N
		  Which pair should be measured. Typically a cable has 4 pairs.
		  0 = Pair A, 1 = Pair B, ...

       --monitor
	      Listens to netlink notification and displays them.

	   command
		  If  argument	matching  a command is used, ethtool only shows
		  notifications of this type. Without  such  argument  or  with
		  --all, all notification types are shown.

	   devname
		  If  a	 device name is used as argument, only notification for
		  this device are shown. Default is to show  notifications  for
		  all devices.

       --show-tunnels
	      Show  tunnel-related  device  capabilities  and  state.  List UDP
	      ports kernel has programmed the device to parse as VxLAN, or GEN-
	      EVE tunnels.

       --show-module
	      Show the transceiver module's parameters.

       --set-module
	      Set the transceiver module's parameters.

	   power-mode-policy high|auto
		  Set the power mode policy for the module. When set  to  high,
		  the  module  always  operates at high power mode. When set to
		  auto, the module is transitioned by the host	to  high  power
		  mode	when the first port using it is put administratively up
		  and to low power mode when the last port using it is put  ad-
		  ministratively  down. The power mode policy can be set before
		  a module is plugged-in.

       --get-plca-cfg
	      Show the current PLCA parameters for the given interface.

       --set-plca-cfg
	      Change the PLCA settings for the given interface.

	   enable on|off
		  Enables or disables the PLCA function. When the  PLCA	 RS  is
		  disabled  (default),	the PHY operates in plain CSMA/CD mode.
		  To enable PLCA, the PHY must be  assigned  a	unique	plca-id
		  other	 than 255. This one can be configured concurrently with
		  the enable parameter.	 The  enable  parameter	 maps  to  IEEE
		  802.3cg-2019	clause 30.16.1.1.1 (aPLCAAdminState) and clause
		  30.16.1.2.1 (acPLCAAdminControl).

	   node-id N
		  The unique node identifier in the range [0 .. 255]. Node ID 0
		  is reserved for the coordinator node, the one generating  the
		  BEACON  signal.  There  must	be exactly one coordinator on a
		  PLCA network. Setting the node ID to 255  (default)  disables
		  the  node.  This  parameter  maps to IEEE 802.3cg-2019 clause
		  30.16.1.1.4 (aPLCALocalNodeID).

	   node-cnt N
		  The node-cnt [1 .. 255] should be set after the maximum  num-
		  ber  of  nodes that can be plugged to the multi-drop network.
		  This parameter regulates the minimum length of the  PLCA  cy-
		  cle.	Therefore,  it	is  only meaningful for the coordinator
		  node (nod-id = 0). Setting this parameter on a follower  node
		  has	no   effect.   The  node-cnt  parameter	 maps  to  IEEE
		  802.3cg-2019 clause 30.16.1.1.3 (aPLCANodeCount).

	   to-tmr N
		  The TO timer parameter sets the value of the transmit	 oppor-
		  tunity  timer in bit-times, and shall be set equal across all
		  the nodes sharing the same medium for PLCA to work.  The  de-
		  fault value of 32 is enough to cover a link of roughly 50 mt.
		  This	parameter maps to  IEEE 802.3cg-2019 clause 30.16.1.1.5
		  (aPLCATransmitOpportunityTimer).

	   burst-cnt N
		  The burst-cnt parameter [0 .. 255] indicates the extra number
		  of packets that the node is allowed to send during  a	 single
		  transmit opportunity.	 By default, this attribute is 0, mean-
		  ing that the node can send a sigle frame per TO. When greater
		  than	0,  the	 PLCA  RS  keeps the TO after any transmission,
		  waiting for the MAC to send a new frame for up  to  burst-tmr
		  BTs. This can only happen a number of times per PLCA cycle up
		  to  the  value  of  this parameter.  After that, the burst is
		  over and the normal counting of TOs resumes.	This  parameter
		  maps	to IEEE 802.3cg-2019 clause 30.16.1.1.6 (aPLCAMaxBurst-
		  Count).

	   burst-tmr N
		  The burst-tmr parameter [0 .. 255] sets  how	many  bit-times
		  the  PLCA RS waits for the MAC to initiate a new transmission
		  when burst-cnt is greater than 0. If the MAC fails to send  a
		  new  frame  within this time, the burst ends and the counting
		  of TOs resumes. Otherwise, the new frame is sent as  part  of
		  the  current	burst. This parameter maps to IEEE 802.3cg-2019
		  clause 30.16.1.1.7 (aPLCABurstTimer). The value of  burst-tmr
		  should  be set greater than the Inter-Frame-Gap (IFG) time of
		  the MAC (plus some margin) for PLCA burst mode to work as in-
		  tended.

       --get-plca-status
	      Show the current PLCA status for the given interface. If on,  the
	      PHY is successfully receiving or generating the BEACON signal. If
	      off, the PLCA function is temporarily disabled and the PHY is op-
	      erating in plain CSMA/CD mode.

       --show-mm
	      Show  the	 MAC  Merge  layer state. The ethtool argument -I --in-
	      clude-statistics can be used with this  command,	and  MAC  Merge
	      layer statistics counters will also be retrieved.

	   pmac-enabled
		  Shows	 whether  the  pMAC is enabled and capable of receiving
		  traffic and SMD-V frames (and responding to them  with  SMD-R
		  replies).

	   tx-enabled
		  Shows	 whether  transmission	on the pMAC is administratively
		  enabled.

	   tx-active
		  Shows whether transmission on the pMAC is  active  (verifica-
		  tion is either successful, or was disabled).

	   tx-min-frag-size
		  Shows	 the  minimum size (in octets) of transmitted non-final
		  fragments which can be received by the link  partner.	 Corre-
		  sponds  to the standard addFragSize variable using the formu-
		  la:

		  tx-min-frag-size = 64 * (1 + addFragSize) - 4

	   rx-min-frag-size
		  Shows the minimum size (in  octets)  of  non-final  fragments
		  which the local device supports receiving.

	   verify-enabled
		  Shows whether the verification state machine is enabled. This
		  process,  if	successful,  ensures  that  preemptible	 frames
		  transmitted by the local device will not be dropped as  error
		  frames by the link partner.

	   verify-time
		  Shows	 the interval in ms between verification attempts, rep-
		  resented as an integer between 1 and 128 ms. The standard de-
		  fines a fixed number of verification	attempts  (verifyLimit)
		  before failing the verification process.

	   max-verify-time
		  Shows the maximum value for verify-time accepted by the local
		  device, which may be less than 128 ms.

	   verify-status
		  Shows	 the current state of the verification state machine of
		  the local device.  Values can be INITIAL, VERIFYING, SUCCEED-
		  ED, FAILED or DISABLED.

       --set-mm
	      Set the MAC Merge layer parameters.

	   pmac-enabled	 on|off
		  Enable reception for the pMAC.

	   tx-enabled  on|off
		  Administatively enable transmission for the pMAC.

	   tx-min-frag-size  N
		  Set the minimum size (in  octets)  of	 transmitted  non-final
		  fragments which can be received by the link partner.

	   verify-enabled  on|off
		  Enable or disable the verification state machine.

	   verify-time	N
		  Set the interval in ms between verification attempts.

       --show-pse
	      Show  the	 current  Power Sourcing Equipment (PSE) status for the
	      given interface.

	   podl-pse-admin-state
		  This attribute indicates the operational status of  PoDL  PSE
		  functions,  which  can  be modified using the podl-pse-admin-
		  control  parameter.  It  corresponds	 to   IEEE   802.3-2018
		  30.15.1.1.2 (aPoDLPSEAdminState), with potential values being
		  enabled, disabled

	   podl-pse-power-detection-status
		  This	attribute  indicates  the power detection status of the
		  PoDL PSE. The status depend on internal PSE state machine and
		  automatic PD classification support. It corresponds  to  IEEE
		  802.3-2018  30.15.1.1.3  (aPoDLPSEPowerDetectionStatus)  with
		  potential values being disabled, searching, delivering power,
		  sleep, idle, error

	   c33-pse-admin-state
		  This attribute indicates the operational status  of  c33  PSE
		  functions, which can be modified using the c33-pse-admin-con-
		  trol	parameter. It corresponds to IEEE 802.3-2022 30.9.1.1.2
		  (aPSEAdminState), with potential values being	 enabled,  dis-
		  abled

	   c33-pse-power-detection-status
		  This	attribute  indicates  the power detection status of the
		  c33 PSE. The status depend on internal PSE state machine  and
		  automatic  PD	 classification support. It corresponds to IEEE
		  802.3-2022 30.9.1.1.5 (aPSEPowerDetectionStatus) with	 poten-
		  tial	values	being  disabled,  searching,  delivering power,
		  test, fault, other fault

	   c33-pse-extended-state
		  This attribute indicates the Extended state of the  c33  PSE.
		  The  extended state correlated with the c33 PSE Extended Sub-
		  state allows to have more detail on the c33 PSE current error
		  state.  It corresponds to IEEE 802.3-2022 33.2.4.4 Variables.

	   c33-pse-extended-substate
		  This attribute indicates the Extended	 substate  of  the  c33
		  PSE. Correlated with the c33 PSE Extended state value, it al-
		  lows to have more detail on the c33 PSE current error state.

	   c33-pse-power-class
		  This	attribute identifies the power class of the c33 PSE. It
		  depends on the class negotiated between the PSE and  the  PD.
		  It  corresponds to IEEE 802.3-2022 30.9.1.1.8 (aPSEPowerClas-
		  sification).

	   c33-pse-actual-power
		  This attribute identifies the actual power drawn by  the  c33
		  PSE.	 It  corresponds  to  ``IEEE  802.3-2022``  30.9.1.1.23
		  (aPSEActualPower). Actual power is reported in mW.

	   c33-pse-available-power-limit
		  This attribute identifies the configured c33 PSE power  limit
		  in mW.

	   c33-pse-power-limit-ranges
		  This attribute specifies the allowed power limit ranges in mW
		  for  configuring the c33-pse-avail-pw-limit parameter. It de-
		  fines the valid power levels that can be assigned to the  c33
		  PSE in compliance with the c33 standard.

       --set-pse
	      Set Power Sourcing Equipment (PSE) parameters.

	   podl-pse-admin-control  enable|disable
		  This	parameter  manages  PoDL PSE Admin operations in accor-
		  dance with the IEEE 802.3-2018  30.15.1.2.1  (acPoDLPSEAdmin-
		  Control) specification.

	   c33-pse-admin-control  enable|disable
		  This parameter manages c33 PSE Admin operations in accordance
		  with the IEEE 802.3-2022 30.9.1.2.1 (acPSEAdminControl) spec-
		  ification.

	   c33-pse-avail-pw-limit  N
		  This	parameter  manages c33 PSE Available Power Limit in mW,
		  in accordance with the  IEEE	802.3-2022  33.2.4.4  Variables
		  (pse_available_power) specification.

       --flash-module-firmware
	      Flash  the  transceiver  module's	 firmware.  The firmware update
	      process is composed  from	 three	logical	 steps.	 Downloading  a
	      firmware	image  to the transceiver module, running the image and
	      committing the image so that it is run  upon  reset.  When  flash
	      command is given, the firmware update process is performed in its
	      entirety in that order.

	   file FILE
		  Specifies the filename of the transceiver module firmware im-
		  age.	The  firmware must first be installed in one of the di-
		  rectories where the kernel firmware loader or firmware  agent
		  will look, such as /lib/firmware. The firmware image is down-
		  loaded  to the transceiver module, validated, run and commit-
		  ted.

	   pass PASS
		  Optional transceiver module password that might  be  required
		  as part of the transceiver module firmware update process.

       --show-phys
	      Show  the	 PHY devices attached to an interface, and the way they
	      link together.

	   phy_index
		  The PHY's index, that identifies it within the network inter-
		  face. If the interface has multiple PHYs, they will each have
		  a unique index on that interface. This index can then be used
		  for commands that targets PHYs.

	   drvname
		  The name of the driver bound to this PHY device.

	   name	  The PHY's device name, matching the name found in sysfs.

	   downstream_sfp_name
		  If the PHY drives an SFP cage, this field contains  the  name
		  of the associated SFP bus.

	   upstream_type  mac | phy
		  Indicates the nature of the device the PHY is attached to.

	   upstream_index
		  If  the PHY's upstream_type is phy , this field indicates the
		  phy_index of the upstream phy.

	   upstream_sfp_name
		  If the PHY is withing an SFP/SFF module, this field  contains
		  the name of the upstream SFP bus.

BUGS
       Not supported (in part or whole) on all network drivers.

AUTHOR
       ethtool was written by David Miller.

       Modifications  by Jeff Garzik, Tim Hockin, Jakub Jelinek, Andre Majorel,
       Eli Kupermann, Scott  Feldman,  Andi  Kleen,  Alexander	Duyck,	Sucheta
       Chakraborty, Jesse Brandeburg, Ben Hutchings, Scott Branden.

AVAILABILITY
       ethtool	 is   available	  from	http://www.kernel.org/pub/software/net-
       work/ethtool/

Ethtool version 6.14.2		   July 2025			     ETHTOOL(8)