search..
No manual entry for -- in section 7
udplite(7)		Miscellaneous Information Manual	     udplite(7)

NAME
       udplite - Lightweight User Datagram Protocol

SYNOPSIS
       #include <sys/socket.h>

       sockfd = socket(AF_INET, SOCK_DGRAM, IPPROTO_UDPLITE);

DESCRIPTION
       This  is	 an  implementation  of	 the Lightweight User Datagram Protocol
       (UDP-Lite), as described in RFC 3828.

       UDP-Lite is an extension of UDP	(RFC 768)  to  support	variable-length
       checksums.   This  has advantages for some types of multimedia transport
       that may be able to make use of slightly damaged datagrams, rather  than
       having them discarded by lower-layer protocols.

       The variable-length checksum coverage is set via a setsockopt(2) option.
       If  this	 option	 is not set, the only difference from UDP is in using a
       different IP protocol identifier (IANA number 136).

       The UDP-Lite implementation is a full extension of udp(7)--that	is,  it
       shares  the same API and API behavior, and in addition offers two socket
       options to control the checksum coverage.

   Address format
       UDP-Litev4 uses the sockaddr_in address format described in ip(7).  UDP-
       Litev6 uses the sockaddr_in6 address format described in ipv6(7).

   Socket options
       To set or get a UDP-Lite socket option, call getsockopt(2)  to  read  or
       setsockopt(2)  to write the option with the option level argument set to
       IPPROTO_UDPLITE.	 In addition, all IPPROTO_UDP socket options are  valid
       on a UDP-Lite socket.  See udp(7) for more information.

       The following two options are specific to UDP-Lite.

       UDPLITE_SEND_CSCOV
	      This option sets the sender checksum coverage and takes an int as
	      argument, with a checksum coverage value in the range 0..2^16-1.

	      A	 value	of  0 means that the entire datagram is always covered.
	      Values from 1-7 are illegal (RFC 3828, 3.1) and are rounded up to
	      the minimum coverage of 8.

	      With regard to IPv6 jumbograms (RFC 2675), the UDP-Litev6	 check-
	      sum  coverage  is	 limited  to  the  first  2^16-1 octets, as per
	      RFC 3828, 3.5.  Higher values are therefore silently truncated to
	      2^16-1.  If in doubt, the current coverage value	can  always  be
	      queried using getsockopt(2).

       UDPLITE_RECV_CSCOV
	      This  is	the  receiver-side  analogue and uses the same argument
	      format and value range as UDPLITE_SEND_CSCOV.  This option is not
	      required to enable traffic with partial checksum	coverage.   Its
	      function	is that of a traffic filter: when enabled, it instructs
	      the kernel to drop all packets which have a  coverage  less  than
	      the specified coverage value.

	      When  the	 value	of UDPLITE_RECV_CSCOV exceeds the actual packet
	      coverage, incoming packets are silently dropped, but may generate
	      a warning message in the system log.

ERRORS
       All errors documented for udp(7) may be returned.  UDP-Lite does not add
       further errors.

FILES
       /proc/net/snmp
	      Basic UDP-Litev4 statistics counters.

       /proc/net/snmp6
	      Basic UDP-Litev6 statistics counters.

VERSIONS
       UDP-Litev4/v6 first appeared in Linux 2.6.20.

BUGS
       Where glibc support is missing, the following definitions are needed:

	   #define IPPROTO_UDPLITE     136
	   #define UDPLITE_SEND_CSCOV  10
	   #define UDPLITE_RECV_CSCOV  11

SEE ALSO
       ip(7), ipv6(7), socket(7), udp(7)

       RFC 3828 for the Lightweight User Datagram Protocol (UDP-Lite).

       Documentation/networking/udplite.txt in the Linux kernel source tree

Linux man-pages 6.9.1		   2024-05-02			     udplite(7)