search..
No manual entry for -- in section 7
icmp(7)			Miscellaneous Information Manual		icmp(7)

NAME
       icmp - Linux IPv4 ICMP kernel module.

DESCRIPTION
       This kernel protocol module implements the Internet Control Message Pro-
       tocol defined in RFC 792.  It is used to signal error conditions and for
       diagnosis.  The user doesn't interact directly with this module; instead
       it  communicates	 with  the other protocols in the kernel and these pass
       the ICMP errors to the application layers.  The kernel ICMP module  also
       answers ICMP requests.

       A  user protocol may receive ICMP packets for all local sockets by open-
       ing a raw socket with the protocol IPPROTO_ICMP.	 See  raw(7)  for  more
       information.  The types of ICMP packets passed to the socket can be fil-
       tered  using  the  ICMP_FILTER  socket  option.	ICMP packets are always
       processed by the kernel too, even when passed to a user socket.

       Linux limits the	 rate  of  ICMP	 error	packets	 to  each  destination.
       ICMP_REDIRECT  and ICMP_DEST_UNREACH are also limited by the destination
       route of the incoming packets.

   /proc interfaces
       ICMP supports a set of /proc interfaces to configure some global IP  pa-
       rameters.  The parameters can be accessed by reading or writing files in
       the  directory  /proc/sys/net/ipv4/.   Most of these parameters are rate
       limitations for specific ICMP types.  Linux 2.2 uses a token bucket fil-
       ter to limit ICMPs.  The value is the timeout in jiffies until the token
       bucket filter is cleared after a burst.	A jiffy is a  system  dependent
       unit, usually 10ms on i386 and about 1ms on alpha and ia64.

       icmp_destunreach_rate (Linux 2.2 to Linux 2.4.9)
	      Maximum  rate to send ICMP Destination Unreachable packets.  This
	      limits the rate at which packets are sent to any individual route
	      or  destination.	 The  limit  does   not	  affect   sending   of
	      ICMP_FRAG_NEEDED packets needed for path MTU discovery.

       icmp_echo_ignore_all (since Linux 2.2)
	      If  this	value  is  nonzero, Linux will ignore all ICMP_ECHO re-
	      quests.

       icmp_echo_ignore_broadcasts (since Linux 2.2)
	      If this value is nonzero, Linux will ignore all ICMP_ECHO packets
	      sent to broadcast addresses.

       icmp_echoreply_rate (Linux 2.2 to Linux 2.4.9)
	      Maximum rate for sending ICMP_ECHOREPLY packets  in  response  to
	      ICMP_ECHOREQUEST packets.

       icmp_errors_use_inbound_ifaddr (Boolean; default: disabled; since Linux
       2.6.12)
	      If  disabled,  ICMP  error messages are sent with the primary ad-
	      dress of the exiting interface.

	      If enabled, the message will be sent with the primary address  of
	      the  interface  that received the packet that caused the ICMP er-
	      ror.  This is the behavior that many network administrators  will
	      expect from a router.  And it can make debugging complicated net-
	      work layouts much easier.

	      Note  that  if  no  primary  address exists for the interface se-
	      lected, then the primary address of the first non-loopback inter-
	      face that has one will be used regardless of this setting.

       icmp_ignore_bogus_error_responses (Boolean; default: disabled; since
       Linux 2.2)
	      Some routers violate RFC1122 by sending bogus responses to broad-
	      cast frames.  Such violations are normally logged	 via  a	 kernel
	      warning.	 If this parameter is enabled, the kernel will not give
	      such warnings, which will avoid log file clutter.

       icmp_paramprob_rate (Linux 2.2 to Linux 2.4.9)
	      Maximum rate for sending ICMP_PARAMETERPROB packets.  These pack-
	      ets are sent when a packet arrives with an invalid IP header.

       icmp_ratelimit (integer; default: 1000; since Linux 2.4.10)
	      Limit the maximum rates  for  sending  ICMP  packets  whose  type
	      matches icmp_ratemask (see below) to specific targets.  0 to dis-
	      able  any limiting, otherwise the minimum space between responses
	      in milliseconds.

       icmp_ratemask (integer; default: see below; since Linux 2.4.10)
	      Mask made of ICMP types for which rates are being limited.

	      Significant bits: IHGFEDCBA9876543210
	      Default mask:	0000001100000011000 (0x1818)

	      Bit  definitions	(see  the  Linux   kernel   source   file   in-
	      clude/linux/icmp.h):
		   0 Echo Reply
		   3 Destination Unreachable *
		   4 Source Quench *
		   5 Redirect
		   8 Echo Request
		   B Time Exceeded *
		   C Parameter Problem *
		   D Timestamp Request
		   E Timestamp Reply
		   F Info Request
		   G Info Reply
		   H Address Mask Request
		   I Address Mask Reply

       The  bits  marked  with an asterisk are rate limited by default (see the
       default mask above).

       icmp_timeexceed_rate (Linux 2.2 to Linux 2.4.9)
	      Maximum rate for sending ICMP_TIME_EXCEEDED packets.  These pack-
	      ets are sent to prevent loops when a packet has crossed too  many
	      hops.

       ping_group_range (two integers; default: see below; since Linux 2.6.39)
	      Range of the group IDs (minimum and maximum group IDs, inclusive)
	      that  are allowed to create ICMP Echo sockets.  The default is "1
	      0", which means no group is allowed to create ICMP Echo sockets.

VERSIONS
       Support for the ICMP_ADDRESS request was removed in Linux 2.2.

       Support for ICMP_SOURCE_QUENCH was removed in Linux 2.2.

NOTES
       As many other implementations don't support  IPPROTO_ICMP  raw  sockets,
       this feature should not be relied on in portable programs.

       ICMP_REDIRECT packets are not sent when Linux is not acting as a router.
       They  are also accepted only from the old gateway defined in the routing
       table and the redirect routes are expired after some time.

       The 64-bit timestamp returned by ICMP_TIMESTAMP is in milliseconds since
       the Epoch, 1970-01-01 00:00:00 +0000 (UTC).

       Linux ICMP internally uses a raw socket to send ICMPs.  This raw	 socket
       may appear in netstat(8) output with a zero inode.

SEE ALSO
       ip(7), rdisc(8)

       RFC 792 for a description of the ICMP protocol.

Linux man-pages 6.9.1		   2024-05-02				icmp(7)