search..
No manual entry for -- in section 1
BUSYBOX(1)			    busybox			     BUSYBOX(1)

NAME
       BusyBox - The Swiss Army Knife of Embedded Linux

SYNTAX
	busybox <applet> [arguments...]	 # or

	<applet> [arguments...]		 # if symlinked

DESCRIPTION
       BusyBox combines tiny versions of many common UNIX utilities into a
       single small executable. It provides minimalist replacements for most of
       the utilities you usually find in GNU coreutils, util-linux, etc. The
       utilities in BusyBox generally have fewer options than their full-
       featured GNU cousins; however, the options that are included provide the
       expected functionality and behave very much like their GNU counterparts.

       BusyBox has been written with size-optimization and limited resources in
       mind.  It is also extremely modular so you can easily include or exclude
       commands (or features) at compile time. This makes it easy to customize
       your embedded systems. To create a working system, just add /dev, /etc,
       and a Linux kernel.  BusyBox provides a fairly complete POSIX
       environment for any small or embedded system.

       BusyBox is extremely configurable.  This allows you to include only the
       components you need, thereby reducing binary size. Run 'make config' or
       'make menuconfig' to select the functionality that you wish to enable.
       Then run 'make' to compile BusyBox using your configuration.

       After the compile has finished, you should use 'make install' to install
       BusyBox. This will install the 'bin/busybox' binary, in the target
       directory specified by CONFIG_PREFIX. CONFIG_PREFIX can be set when
       configuring BusyBox, or you can specify an alternative location at
       install time (i.e., with a command line like 'make
       CONFIG_PREFIX=/tmp/foo install'). If you enabled any applet installation
       scheme (either as symlinks or hardlinks), these will also be installed
       in the location pointed to by CONFIG_PREFIX.

USAGE
       BusyBox is a multi-call binary.	A multi-call binary is an executable
       program that performs the same job as more than one utility program.
       That means there is just a single BusyBox binary, but that single binary
       acts like a large number of utilities.  This allows BusyBox to be
       smaller since all the built-in utility programs (we call them applets)
       can share code for many common operations.

       You can also invoke BusyBox by issuing a command as an argument on the
       command line.  For example, entering

	       /bin/busybox ls

       will also cause BusyBox to behave as 'ls'.

       Of course, adding '/bin/busybox' into every command would be painful.
       So most people will invoke BusyBox using links to the BusyBox binary.

       For example, entering

	       ln -s /bin/busybox ls
	       ./ls

       will cause BusyBox to behave as 'ls' (if the 'ls' command has been
       compiled into BusyBox).	Generally speaking, you should never need to
       make all these links yourself, as the BusyBox build system will do this
       for you when you run the 'make install' command.

       If you invoke BusyBox with no arguments, it will provide you with a list
       of the applets that have been compiled into your BusyBox binary.

COMMON OPTIONS
       Most BusyBox applets support the --help argument to provide a terse
       runtime description of their behavior.  If the
       CONFIG_FEATURE_VERBOSE_USAGE option has been enabled, more detailed
       usage information will also be available.

COMMANDS
       Currently available applets include:

	       [, [[, acpid, adjtimex, ar, arch, arp, arping, ascii, ash, awk,
	       base64, basename, bc, blkdiscard, blkid, blockdev, brctl, bunzip2,
	       bzcat, bzip2, cal, cat, chgrp, chmod, chown, chroot, chvt, clear,
	       cmp, cp, cpio, crc32, crond, crontab, cttyhack, cut, date, dc, dd,
	       deallocvt, depmod, devmem, df, diff, dirname, dmesg, dnsdomainname,
	       dos2unix, dpkg, dpkg-deb, du, dumpkmap, dumpleases, echo, ed, egrep,
	       env, expand, expr, factor, fallocate, false, fatattr, fdisk, fgrep,
	       find, findfs, fold, free, freeramdisk, fsfreeze, fstrim, ftpget,
	       ftpput, getfattr, getopt, getty, grep, groups, gunzip, gzip, halt,
	       head, hexdump, hostid, hostname, httpd, hwclock, i2cdetect, i2cdump,
	       i2cget, i2cset, i2ctransfer, id, ifconfig, ifdown, ifup, init,
	       insmod, install, ionice, ip, ipcalc, kill, killall, klogd, last,
	       less, link, linux32, linux64, linuxrc, ln, loadfont, loadkmap,
	       logger, login, logname, logread, losetup, ls, lsmod, lsscsi, lzcat,
	       lzma, lzop, md5sum, mdev, microcom, mim, mkdir, mkdosfs, mke2fs,
	       mkfifo, mknod, mkpasswd, mkswap, mktemp, modinfo, modprobe, more,
	       mount, mt, mv, nameif, nbd-client, nc, netstat, nl, nologin, nproc,
	       nsenter, nslookup, nuke, od, openvt, partprobe, passwd, paste,
	       patch, pidof, ping, ping6, pivot_root, poweroff, printf, ps, pwd,
	       rdate, readlink, realpath, reboot, renice, reset, resume, rev, rm,
	       rmdir, rmmod, route, rpm, rpm2cpio, run-init, run-parts, sed, seq,
	       setkeycodes, setpriv, setsid, sh, sha1sum, sha256sum, sha3sum,
	       sha512sum, shred, shuf, sleep, sort, ssl_client, start-stop-daemon,
	       stat, strings, stty, su, sulogin, svc, svok, swapoff, swapon,
	       switch_root, sync, sysctl, syslogd, tac, tail, tar, taskset, tc,
	       tee, telnet, test, tftp, time, timeout, top, touch, tr, traceroute,
	       traceroute6, true, truncate, ts, tty, tunctl, ubirename, udhcpc,
	       udhcpc6, udhcpd, uevent, umount, uname, uncompress, unexpand, uniq,
	       unix2dos, unlink, unlzma, unshare, unxz, unzip, uptime, usleep,
	       uudecode, uuencode, vconfig, vi, w, watch, watchdog, wc, wget,
	       which, who, whoami, xargs, xxd, xz, xzcat, yes, zcat

COMMAND DESCRIPTIONS
       acpid
	   acpid  [-df]	 [-c CONFDIR] [-l LOGFILE] [-a ACTIONFILE] [-M MAPFILE]
	   [-e PROC_EVENT_FILE] [-p PIDFILE]

	   Listen to ACPI events and spawn specific helpers on event arrival

		   -d	   Log to stderr, not log file (implies -f)
		   -f	   Run in foreground
		   -c DIR  Config directory [/etc/acpi]
		   -e FILE /proc event file [/proc/acpi/event]
		   -l FILE Log file [/var/log/acpid.log]
		   -p FILE Pid file [/var/run/acpid.pid]
		   -a FILE Action file [/etc/acpid.conf]
		   -M FILE Map file [/etc/acpi.map]

	   Accept and ignore compatibility options -g -m -s -S -v

       adjtimex
	   adjtimex [-q] [-o OFS] [-f FREQ] [-p TCONST] [-t TICK]

	   Read or set kernel time variables. See adjtimex(2)

		   -q	   Quiet
		   -o OFF  Time offset, microseconds
		   -f FREQ Frequency adjust, integer kernel units (65536 is 1ppm)
		   -t TICK Microseconds per tick, usually 10000
			   (positive -t or -f values make clock run faster)
		   -p TCONST

       ar  ar x|p|t [-ov] ARCHIVE [FILE]...

	   Extract or list FILEs from an ar archive

		   x	   Extract
		   p	   Extract to stdout
		   t	   List
		   -o	   Restore mtime
		   -v	   Verbose

       arch
	   arch

	   Print system architecture

       arp arp [-vn]	 [-H HWTYPE] [-i IF] -a	 [HOSTNAME]  [-v]	    [-i
	   IF]	-d  HOSTNAME  [pub] [-v] [-H HWTYPE] [-i IF] -s HOSTNAME HWADDR
	   [temp] [-v] [-H HWTYPE] [-i IF] -s HOSTNAME	HWADDR	[netmask  MASK]
	   pub [-v] [-H HWTYPE] [-i IF] -Ds HOSTNAME IFACE [netmask MASK] pub

	   Manipulate ARP cache

		   -a		   Displatroff:<standard input>:648: warning [p 7, 11.3i]: cannot adjust line
y (all) hosts
		   -d		   Delete ARP entry
		   -s		   Set new entry
		   -v		   Verbose
		   -n		   Don't resolve names
		   -i IF	   Network interface
		   -D		   Read HWADDR from IFACE
		   -A,-p AF	   Protocol family
		   -H HWTYPE	   Hardware address type

       arping
	   arping [-fqbDUA] [-c CNT] [-w TIMEOUT] [-I IFACE] [-s SRC_IP] DST_IP

	   Send ARP requests/replies

		   -f		   Quit on first ARP reply
		   -q		   Quiet
		   -b		   Keep broadcasting, don't go unicast
		   -D		   Exit with 1 if DST_IP replies
		   -U		   Unsolicited ARP mode, update your neighbors
		   -A		   ARP answer mode, update your neighbors
		   -c N		   Stop after sending N ARP requests
		   -w TIMEOUT	   Seconds to wait for ARP reply
		   -I IFACE	   Interface to use (default eth0)
		   -s SRC_IP	   Sender IP address
		   DST_IP	   Target IP address

       ash ash	[-il]  [-|+Cabefmnuvx] [-|+o OPT]... [-c 'SCRIPT' [ARG0 ARGS] |
	   FILE ARGS | -s ARGS]

	   Unix shell interpreter

       awk awk [OPTIONS] [AWK_PROGRAM] [FILE]...

		   -v VAR=VAL	   Set variable
		   -F SEP	   Use SEP as field separator
		   -f/-E FILE	   Read program from FILE
		   -e AWK_PROGRAM

       base64
	   base64 [-d] [-w COL] [FILE]

	   Base64 encode or decode FILE to standard output

		   -d	   Decode data
		   -w COL  Wrap lines at COL (default 76, 0 disables)

       basename
	   basename FILE [SUFFIX] | -a FILE... | -s SUFFIX FILE...

	   Strip directory path and SUFFIX from FILE

		   -a		   All arguments are FILEs
		   -s SUFFIX	   Remove SUFFIX (implies -a)

       bc  bc [-sqlw] [FILE]...

	   Arbitrary precision calculator

		   -q	   Quiet
		   -l	   Load standard library
		   -s	   Be POSIX compatible
		   -w	   Warn if extensions are used

	   $BC_LINE_LENGTH changes output width

       blkdiscard
	   blkdiscard [-o OFS] [-l LEN] [-s] DEVICE

	   Discard sectors on DEVICE

		   -o OFS  Byte offset into device
		   -l LEN  Number of bytes to discard
		   -s	   Perform a secure discard

       blkid
	   blkid [BLOCKDEV]...

	   Print UUIDs of all filesystems

       blockdev
	   blockdev OPTION BLOCKDEV

		   --setro	   Set ro
		   --setrw	   Set rw
		   --getro	   Get ro
		   --getss	   Get sector size
		   --getbsz	   Get block size
		   --setbsz BYTES  Set block size
		   --getsz	   Get device size in 512-byte sectors
		   --getsize64	   Get device size in bytes
		   --getra	   Get readahead in 512-byte sectors
		   --setra SECTORS Set readahead
		   --flushbufs	   Flush buffers
		   --rereadpt	   Reread partition table

       brctl
	   brctl COMMAND [BRIDGE [ARGS]]

	   Manage ethernet bridges Commands:

		   addbr BRIDGE		   Create BRIDGE
		   delbr BRIDGE		   Delete BRIDGE
		   addif BRIDGE IFACE	   Add IFACE to BRIDGE
		   delif BRIDGE IFACE	   Delete IFACE from BRIDGE

       bunzip2
	   bunzip2 [-cfk] [FILE]...

	   Decompress FILEs (or stdin)

		   -c	   Write to stdout
		   -f	   Force
		   -k	   Keep input files
		   -t	   Test integrity

       bzcat
	   bzcat [FILE]...

	   Decompress to stdout

       bzip2
	   bzip2 [-cfkdt123456789] [FILE]...

	   Compress FILEs (or stdin) with bzip2 algorithm

		   -1..9   Compression level
		   -d	   Decompress
		   -c	   Write to stdout
		   -f	   Force
		   -k	   Keep input files
		   -t	   Test integrity

       cal cal [-jmy] [[MONTH] YEAR]

	   Display a calendar

		   -j	   Use julian dates
		   -m	   Week starts on Monday
		   -y	   Display the entire year

       cat cat [-nbvteA] [FILE]...

	   Print FILEs to stdout

		   -n	   Number output lines
		   -b	   Number nonempty lines
		   -v	   Show nonprinting characters as ^x or M-x
		   -t	   ...and tabs as ^I
		   -e	   ...and end lines with $
		   -A	   Same as -vte

       chgrp
	   chgrp [-RhLHPcvf]... GROUP FILE...

	   Change the group membership of FILEs to GROUP

		   -h	   Affect symlinks instead of symlink targets
		   -L	   Traverse all symlinks to directories
		   -H	   Traverse symlinks on command line only
		   -P	   Don't traverse symlinks (default)
		   -R	   Recurse
		   -c	   List changed files
		   -v	   Verbose
		   -f	   Hide errors

       chmod
	   chmod [-Rcvf] MODE[,MODE]... FILE...

	   MODE	  is   octal   number	 (bit	 pattern    sstrwxrwxrwx)    or
	   [ugoa]{+|-|=}[rwxXst]

		   -R	   Recurse
		   -c	   List changed files
		   -v	   Verbose
		   -f	   Hide errors

       chown
	   chown [-RhLHPcvf]... USER[:[GRP]] FILE...

	   Change the owner and/or group of FILEs to USER and/or GRP

		   -h	   Affect symlinks instead of symlink targets
		   -L	   Traverse all symlinks to directories
		   -H	   Traverse symlinks on command line only
		   -P	   Don't traverse symlinks (default)
		   -R	   Recurse
		   -c	   List changed files
		   -v	   Verbose
		   -f	   Hide errors

       chroot
	   chroot NEWROOT [PROG ARGS]

	   Run PROG with root directory set to NEWROOT

       chvt
	   chvt N

	   Change the foreground virtual terminal to /dev/ttyN

       clear
	   clear

	   Clear screen

       cmp cmp [-ls] [-n NUM] FILE1 [FILE2 [SKIP1 [SKIP2]]]

	   Compare FILE1 with FILE2 (or stdin)

		   -l	   Write the byte numbers (decimal) and values (octal)
			   for all differing bytes
		   -s	   Quiet
		   -n NUM  Compare at most NUM bytes

       cp  cp  [-arPLHpfinlsTu]	 SOURCE DEST or: cp [-arPLHpfinlsu] SOURCE... {
	   -t DIRECTORY | DIRECTORY }

	   Copy SOURCEs to DEST

		   -a	   Same as -dpR
		   -R,-r   Recurse
		   -d,-P   Preserve symlinks (default if -R)
		   -L	   Follow all symlinks
		   -H	   Follow symlinks on command line
		   -p	   Preserve file attributes if possible
		   -f	   Overwrite
		   -i	   Prompt before overwrite
		   -n	   Don't overwrite
		   -l,-s   Create (sym)links
		   -T	   Refuse to copy if DEST is a directory
		   -t DIR  Copy all SOURCEs into DIR
		   -u	   Copy only newer files

       cpio
	   cpio	 [-dmvu]  [-F  FILE]   [-R   USER[:GRP]]   [-H	 newc]	 [-tio]
	   [EXTR_FILE]...

	   Extract  (-i)  or  list  (-t) files from a cpio archive on stdin, or
	   take file list from stdin and create an archive (-o)

	   Main operation mode:

		   -t	   List
		   -i	   Extract EXTR_FILEs (or all)
		   -o	   Create (requires -H newc)
	   Options:

		   -H newc Archive format
		   -d	   Make leading directories
		   -m	   Restore mtime
		   -v	   Verbose
		   -u	   Overwrite
		   -F FILE Input (-t,-i,-p) or output (-o) file
		   -R USER[:GRP]   Set owner of created files
		   -L	   Dereference symlinks
		   -0	   NUL terminated input
		   --ignore-devno
		   --renumber-inodes

       crc32
	   crc32 FILE...

	   Calculate CRC32 checksum of FILEs

       crond
	   crond [-fbS] [-l N] [-L LOGFILE] [-c DIR]

		   -f	   Foreground
		   -b	   Background (default)
		   -S	   Log to syslog (default)
		   -l N	   Set log level. Most verbose 0, default 8
		   -L FILE Log to FILE
		   -c DIR  Cron dir. Default:/var/spool/cron/crontabs

       crontab
	   crontab [-c DIR] [-u USER] [-ler]|[FILE]

		   -c	   Crontab directory
		   -u	   User
		   -l	   List crontab
		   -e	   Edit crontab
		   -r	   Delete crontab
		   FILE	   Replace crontab by FILE ('-': stdin)

       cttyhack
	   cttyhack [PROG ARGS]

	   Give PROG a controlling tty if possible.  Example  for  /etc/inittab
	   (for	 busybox  init):       ::respawn:/bin/cttyhack	/bin/sh	 Giving
	   controlling tty to shell running with PID 1:	     $ exec cttyhack sh
	   Starting interactive shell from boot shell script:

		   setsid cttyhack sh

       cut cut [OPTIONS] [FILE]...

	   Print selected fields from FILEs to stdout

		   -b LIST Output only bytes from LIST
		   -c LIST Output only characters from LIST
		   -d SEP  Field delimiter for input (default -f TAB, -F run of whitespace)
		   -O SEP  Field delimiter for output (default = -d for -f, one space for -F)
		   -D	   Don't sort/collate sections or match -fF lines without delimiter
		   -f LIST Print only these fields (-d is single char)
		   -F LIST Print only these fields (-d is regex)
		   -s	   Output only lines containing delimiter
		   -n	   Ignored

       date
	   date [OPTIONS] [+FMT] [[-s] TIME]

	   Display time (using +FMT), or set time

		   -u		   Work in UTC (don't convert to local time)
		   [-s] TIME	   Set time to TIME
		   -d TIME	   Display TIME, not 'now'
		   -D FMT	   FMT (strptime format) for -s/-d TIME conversion
		   -r FILE	   Display last modification time of FILE
		   -R		   Output RFC-2822 date
		   -I[SPEC]	   Output ISO-8601 date
				   SPEC=date (default), hours, minutes, seconds or ns

	   Recognized TIME formats:

		   @seconds_since_1970
		   hh:mm[:ss]
		   [YYYY.]MM.DD-hh:mm[:ss]
		   YYYY-MM-DD hh:mm[:ss]
		   [[[[[YY]YY]MM]DD]hh]mm[.ss]
		   'date TIME' form accepts MMDDhhmm[[YY]YY][.ss] instead

       dc  dc [-x] [-eSCRIPT]... [-fFILE]... [FILE]...

	   Tiny RPN calculator. Operations: Arithmetic: + - * / % ^ ~ -	 divide
	   with	 remainder | - modular exponentiation v - square root p - print
	   top of the stack without popping f - print entire stack k - pop  the
	   value  and  set  precision i - pop the value and set input radix o -
	   pop the value and set output radix Examples: dc -e'2 2 + p' -> 4, dc
	   -e'8 8 * 2 2 + / p' -> 16

       dd  dd  [if=FILE]  [of=FILE]  [ibs=N  obs=N/bs=N]   [count=N]   [skip=N]
	   [seek=N]			      [conv=notrunc|noerror|sync|fsync]
		[iflag=skip_bytes|count_bytes|fullblock|direct]
	   [oflag=seek_bytes|append|direct]

	   Copy a file with converting and formatting

		   if=FILE	   Read from FILE instead of stdin
		   of=FILE	   Write to FILE instead of stdout
		   bs=N		   Read and write N bytes at a time
		   ibs=N	   Read N bytes at a time
		   obs=N	   Write N bytes at a time
		   count=N	   Copy only N input blocks
		   skip=N	   Skip N input blocks
		   seek=N	   Skip N output blocks
		   conv=notrunc	   Don't truncate output file
		   conv=noerror	   Continue after read errors
		   conv=sync	   Pad blocks with zeros
		   conv=fsync	   Physically write data out before finishing
		   conv=swab	   Swap every pair of bytes
		   iflag=skip_bytes	   skip=N is in bytes
		   iflag=count_bytes	   count=N is in bytes
		   oflag=seek_bytes	   seek=N is in bytes
		   iflag=direct	   O_DIRECT input
		   oflag=direct	   O_DIRECT output
		   iflag=fullblock Read full blocks
		   oflag=append	   Open output in append mode
		   status=noxfer   Suppress rate output
		   status=none	   Suppress all output

	   N may be suffixed by c (1), w (2), b (512), kB (1000), k (1024), MB,
	   M, GB, G

       deallocvt
	   deallocvt [N]

	   Deallocate unused virtual terminal /dev/ttyN

       depmod
	   depmod [-n] [-b BASE] [VERSION] [MODFILES]...

	   Generate modules.dep, alias, and symbols files

		   -b BASE Use BASE/lib/modules/VERSION
		   -n	   Dry run: print files to stdout

       devmem
	   devmem ADDRESS [WIDTH [VALUE]]

	   Read/write from physical address

		   ADDRESS Address to act upon
		   WIDTH   Width (8/16/...)
		   VALUE   Data to be written

       df  df [-PkmhTai] [-B SIZE] [-t TYPE] [FILESYSTEM]...

	   Print filesystem usage statistics

		   -P	   POSIX output format
		   -k	   1024-byte blocks (default)
		   -m	   1M-byte blocks
		   -h	   Human readable (e.g. 1K 243M 2G)
		   -T	   Print filesystem type
		   -t TYPE Print only mounts of this type
		   -a	   Show all filesystems
		   -i	   Inodes
		   -B SIZE Blocksize

       diff
	   diff [-abBdiNqrTstw] [-L LABEL] [-S FILE] [-U LINES] FILE1 FILE2

	   Compare files line by line and output the differences between  them.
	   This implementation supports unified diffs only.

		   -a	   Treat all files as text
		   -b	   Ignore changes in the amount of whitespace
		   -B	   Ignore changes whose lines are all blank
		   -d	   Try hard to find a smaller set of changes
		   -i	   Ignore case differences
		   -L	   Use LABEL instead of the filename in the unified header
		   -N	   Treat absent files as empty
		   -q	   Output only whether files differ
		   -r	   Recurse
		   -S	   Start with FILE when comparing directories
		   -T	   Make tabs line up by prefixing a tab when necessary
		   -s	   Report when two files are the same
		   -t	   Expand tabs to spaces in output
		   -U	   Output LINES lines of context
		   -w	   Ignore all whitespace

       dirname
	   dirname FILENAME

	   Strip non-directory suffix from FILENAME

       dmesg
	   dmesg [-cr] [-n LEVEL] [-s SIZE]

	   Print or control the kernel ring buffer

		   -c		   Clear ring buffer after printing
		   -n LEVEL	   Set console logging level
		   -s SIZE	   Buffer size
		   -r		   Print raw message buffer

       dos2unix
	   dos2unix [-ud] [FILE]

	   Convert  FILE  in-place  from  DOS  to Unix format.	When no file is
	   given, use stdin/stdout.

		   -u	   dos2unix
		   -d	   unix2dos

       dpkg
	   dpkg [-ilCPru] [-F OPT] PACKAGE

	   Install, remove and manage Debian packages

		   -i,--install	   Install the package
		   -l,--list	   List of installed packages
		   --configure	   Configure an unpackaged package
		   -P,--purge	   Purge all files of a package
		   -r,--remove	   Remove all but the configuration files for a package
		   --unpack	   Unpack a package, but don't configure it
		   --force-depends Ignore dependency problems
		   --force-confnew Overwrite existing config files when installing
		   --force-confold Keep old config files when installing

       dpkg-deb
	   dpkg-deb [-cefxX] FILE [DIR]

	   Perform actions on Debian packages (.deb)

		   -c	   List files
		   -f	   Print control fields
		   -e	   Extract control files to DIR (default: ./DEBIAN)
		   -x	   Extract files to DIR (no default)
		   -X	   Verbose extract

       du  du [-aHLdclsxhmk] [FILE]...

	   Summarize disk space used for FILEs (or directories)

		   -a	   Show file sizes too
		   -b	   Apparent size (including holes)
		   -L	   Follow all symlinks
		   -H	   Follow symlinks on command line
		   -d N	   Limit output to directories (and files with -a) of depth < N
		   -c	   Show grand total
		   -l	   Count sizes many times if hard linked
		   -s	   Display only a total for each argument
		   -x	   Skip directories on different filesystems
		   -h	   Sizes in human readable format (e.g., 1K 243M 2G)
		   -m	   Sizes in megabytes
		   -k	   Sizes in kilobytes (default)

       dumpkmap
	   dumpkmap > keymap

	   Print a binary keyboard translation table to stdout

       dumpleases
	   dumpleases [-r|-a] [-d] [-f LEASEFILE]

	   Display DHCP leases granted by udhcpd

		   -f FILE Lease file
		   -r	   Show remaining time
		   -a	   Show expiration time
		   -d	   Show time in seconds

       echo
	   echo [-neE] [ARG]...

	   Print ARGs to stdout

		   -n	   No trailing newline
		   -e	   Interpret backslash escapes (\t=tab etc)
		   -E	   Don't interpret backslash escapes (default)

       ed  ed [-p PROMPT] [-s] [FILE]

       env env [-i0] [-u NAME]... [-] [NAME=VALUE]... [PROG ARGS]

	   Print current environment or run PROG after setting up environment

		   -, -i   Start with empty environment
		   -0	   NUL terminated output
		   -u NAME Remove variable from environment

       expand
	   expand [-i] [-t N] [FILE]...

	   Convert tabs to spaces, writing to stdout

		   -i	   Don't convert tabs after non blanks
		   -t	   Tabstops every N chars

       expr
	   expr EXPRESSION

	   Print the value of EXPRESSION

	   EXPRESSION may be:

		   ARG1 | ARG2	   ARG1 if it is neither null nor 0, otherwise ARG2
		   ARG1 & ARG2	   ARG1 if neither argument is null or 0, otherwise 0
		   ARG1 < ARG2	   1 if ARG1 is less than ARG2, else 0. Similarly:
		   ARG1 <= ARG2
		   ARG1 = ARG2
		   ARG1 != ARG2
		   ARG1 >= ARG2
		   ARG1 > ARG2
		   ARG1 + ARG2	   Sum of ARG1 and ARG2. Similarly:
		   ARG1 - ARG2
		   ARG1 * ARG2
		   ARG1 / ARG2
		   ARG1 % ARG2
		   STRING : REGEXP	   Anchored pattern match of REGEXP in STRING
		   match STRING REGEXP	   Same as STRING : REGEXP
		   substr STRING POS LEN   Substring of STRING, POS counts from 1
		   index STRING CHARS	   Index in STRING where any CHARS is found, or 0
		   length STRING	   Length of STRING
		   quote TOKEN		   Interpret TOKEN as a string, even if
					   it is a keyword like 'match' or an
					   operator like '/'
		   (EXPRESSION)		   Value of EXPRESSION

	   Beware that many operators need to be escaped or quoted for	shells.
	   Comparisons	 are   arithmetic   if	both  ARGs  are	 numbers,  else
	   lexicographical. Pattern matches return the string  matched	between
	   \( and \) or null; if \( and \) are not used, they return the number
	   of characters matched or 0.

       factor
	   factor [NUMBER]...

	   Print prime factors

       fallocate
	   fallocate [-o OFS] -l LEN FILE

	   Preallocate space for FILE

		   -o OFS  Offset of range
		   -l LEN  Length of range

       fatattr
	   fatattr [-+rhsvda] FILE...

	   Change file attributes on FAT filesystem

		   -	   Clear attributes
		   +	   Set attributes
		   r	   Read only
		   h	   Hidden
		   s	   System
		   v	   Volume label
		   d	   Directory
		   a	   Archive

       fdisk
	   fdisk [-ul] [-C CYLINDERS] [-H HEADS] [-S SECTORS] [-b SSZ] DISK

	   Change partition table

		   -u		   Start and End are in sectors (instead of cylinders)
		   -l		   Show partition table for each DISK, then exit
		   -b 2048	   (for certain MO disks) use 2048-byte sectors
		   -C CYLINDERS	   Set number of cylinders/heads/sectors
		   -H HEADS	   Typically 255
		   -S SECTORS	   Typically 63

       find
	   find [-HL] [PATH]... [OPTIONS] [ACTIONS]

	   Search  for	files and perform actions on them.  First failed action
	   stops  processing  of  current  file.   Defaults:  PATH  is	current
	   directory, action is '-print'

		   -L,-follow	   Follow symlinks
		   -H		   ...on command line only
		   -xdev	   Don't descend directories on other filesystems
		   -maxdepth N	   Descend at most N levels. -maxdepth 0 applies
				   actions to command line arguments only
		   -mindepth N	   Don't act on first N levels
		   -depth	   Act on directory *after* traversing it

	   Actions:

		   ( ACTIONS )	   Group actions for -o / -a
		   ! ACT	   Invert ACT's success/failure
		   ACT1 [-a] ACT2  If ACT1 fails, stop, else do ACT2
		   ACT1 -o ACT2	   If ACT1 succeeds, stop, else do ACT2
				   Note: -a has higher priority than -o
		   -name PATTERN   Match file name (w/o directory name) to PATTERN
		   -iname PATTERN  Case insensitive -name
		   -path PATTERN   Match path to PATTERN
		   -ipath PATTERN  Case insensitive -path
		   -regex PATTERN  Match path to regex PATTERN
		   -type X	   File type is X (one of: f,d,l,b,c,s,p)
		   -executable	   File is executable
		   -perm MASK	   At least one mask bit (+MASK), all bits (-MASK),
				   or exactly MASK bits are set in file's mode
		   -mtime DAYS	   mtime is greater than (+N), less than (-N),
				   or exactly N days in the past
		   -atime DAYS	   atime +N/-N/N days in the past
		   -ctime DAYS	   ctime +N/-N/N days in the past
		   -mmin MINS	   mtime is greater than (+N), less than (-N),
				   or exactly N minutes in the past
		   -amin MINS	   atime +N/-N/N minutes in the past
		   -cmin MINS	   ctime +N/-N/N minutes in the past
		   -newer FILE	   mtime is more recent than FILE's
		   -inum N	   File has inode number N
		   -samefile FILE  File is same as FILE
		   -user NAME/ID   File is owned by given user
		   -group NAME/ID  File is owned by given group
		   -size N[bck]	   File size is N (c:bytes,k:kbytes,b:512 bytes(def.))
				   +/-N: file size is bigger/smaller than N
		   -links N	   Number of links is greater than (+N), less than (-N),
				   or exactly N
		   -empty	   Match empty file/directory
		   -prune	   If current file is directory, don't descend into it
	   If none of the following actions is specified, -print is assumed
		   -print	   Print file name
		   -print0	   Print file name, NUL terminated
		   -exec CMD ARG ; Run CMD with all instances of {} replaced by
				   file name. Fails if CMD exits with nonzero
		   -exec CMD ARG + Run CMD with {} replaced by list of file names
		   -ok CMD ARG ;   Prompt and run CMD with {} replaced
		   -quit	   Exit

       findfs
	   findfs LABEL=label or UUID=uuid

	   Find a filesystem device based on a label or UUID

       fold
	   fold [-bs] [-w WIDTH] [FILE]...

	   Wrap input lines in FILEs (or stdin), writing to stdout

		   -b	   Count bytes rather than columns
		   -s	   Break at spaces
		   -w	   Use WIDTH columns instead of 80

       free
	   free [-bkmgh]

	   Display free and used memory

       freeramdisk
	   freeramdisk DEVICE

	   Free all memory used by the specified ramdisk

       fsfreeze
	   fsfreeze --[un]freeze MOUNTPOINT

	   Flush and halt writes to MOUNTPOINT

       fstrim
	   fstrim [OPTIONS] MOUNTPOINT

		   -o OFFSET	   Offset in bytes to discard from
		   -l LEN	   Bytes to discard
		   -m MIN	   Minimum extent length
		   -v		   Print number of discarded bytes

       ftpget
	   ftpget [OPTIONS] HOST [LOCAL_FILE] REMOTE_FILE

	   Download a file via FTP

		   -c	   Continue previous transfer
		   -v	   Verbose
		   -u USER Username
		   -p PASS Password
		   -P PORT

       ftpput
	   ftpput [OPTIONS] HOST [REMOTE_FILE] LOCAL_FILE

	   Upload a file to a FTP server

		   -v	   Verbose
		   -u USER Username
		   -p PASS Password
		   -P PORT

       getfattr
	   getfattr [-h] {-d|-n ATTR} FILE...

	   Get extended attributes

		   -h		   Do not follow symlinks
		   -d		   Dump all attributes
		   -n ATTR	   Get attribute ATTR

       getopt
	   getopt [OPTIONS] [--] OPTSTRING PARAMS

		   -a		   Allow long options starting with single -
		   -l LOPT[,...]   Long options to recognize
		   -n PROGNAME	   The name under which errors are reported
		   -o OPTSTRING	   Short options to recognize
		   -q		   No error messages on unrecognized options
		   -Q		   No normal output
		   -s SHELL	   Set shell quoting conventions
		   -T		   Version test (exits with 4)
		   -u		   Don't quote output

	   Example:

	   O=`getopt  -l  bb:  -- ab:c:: "$@"` || exit 1 eval set -- "$O" while
	   true; do	 case "$1" in	   -a)	echo A;	 shift;;       -b|--bb)
	   echo	 "B:'$2'"; shift 2;;	  -c)  case "$2" in	      "")  echo
	   C;	shift	2;;		 *)   echo    "C:'$2'";	   shift    2;;
		     esac;;	 --)  shift; break;;	  *)   echo Error; exit
	   1;;	    esac done

       getty
	   getty [OPTIONS] BAUD_RATE[,BAUD_RATE]... TTY [TERMTYPE]

	   Open TTY, prompt for login name, then invoke /bin/login

		   -h		   Enable hardware RTS/CTS flow control
		   -L		   Set CLOCAL (ignore Carrier Detect state)
		   -m		   Get baud rate from modem's CONNECT status message
		   -n		   Don't prompt for login name
		   -w		   Wait for CR or LF before sending /etc/issue
		   -i		   Don't display /etc/issue
		   -f ISSUE_FILE   Display ISSUE_FILE instead of /etc/issue
		   -l LOGIN	   Invoke LOGIN instead of /bin/login
		   -t SEC	   Terminate after SEC if no login name is read
		   -I INITSTR	   Send INITSTR before anything else
		   -H HOST	   Log HOST into the utmp file as the hostname

	   BAUD_RATE of 0 leaves it unchanged

       grep
	   grep [-HhnlLoqvsrRiwFEz] [-m N] [-A|B|C N] { PATTERN | -e PATTERN...
	   | -f FILE... } [FILE]...

	   Search for PATTERN in FILEs (or stdin)

		   -H	   Add 'filename:' prefix
		   -h	   Do not add 'filename:' prefix
		   -n	   Add 'line_no:' prefix
		   -l	   Show only names of files that match
		   -L	   Show only names of files that don't match
		   -c	   Show only count of matching lines
		   -o	   Show only the matching part of line
		   -q	   Quiet. Return 0 if PATTERN is found, 1 otherwise
		   -v	   Select non-matching lines
		   -s	   Suppress open and read errors
		   -r	   Recurse
		   -R	   Recurse and dereference symlinks
		   -i	   Ignore case
		   -w	   Match whole words only
		   -x	   Match whole lines only
		   -F	   PATTERN is a literal (not regexp)
		   -E	   PATTERN is an extended regexp
		   -z	   NUL terminated input
		   -m N	   Match up to N times per file
		   -A N	   Print N lines of trailing context
		   -B N	   Print N lines of leading context
		   -C N	   Same as '-A N -B N'
		   -e PTRN Pattern to match
		   -f FILE Read pattern from file

       groups
	   groups [USER]

	   Print the groups USER is in

       gunzip
	   gunzip [-cfkt] [FILE]...

	   Decompress FILEs (or stdin)

		   -c	   Write to stdout
		   -f	   Force
		   -k	   Keep input files
		   -t	   Test integrity

       gzip
	   gzip [-cfkdt] [FILE]...

	   Compress FILEs (or stdin)

		   -d	   Decompress
		   -c	   Write to stdout
		   -f	   Force
		   -k	   Keep input files
		   -t	   Test integrity

       halt
	   halt [-d DELAY] [-nfw]

	   Halt the system

		   -d SEC  Delay interval
		   -n	   Do not sync
		   -f	   Force (don't go through init)
		   -w	   Only write a wtmp record

       head
	   head [OPTIONS] [FILE]...

	   Print  first 10 lines of FILEs (or stdin).  With more than one FILE,
	   precede each with a filename header.

		   -n N[bkm]	   Print first N lines
		   -n -N[bkm]	   Print all except N last lines
		   -c [-]N[bkm]	   Print first N bytes
				   (b:*512 k:*1024 m:*1024^2)
		   -q		   Never print headers
		   -v		   Always print headers

       hexdump
	   hexdump  [-bcdoxCv]	[-e  FMT]  [-f	FMT_FILE]  [-n	LEN]  [-s  OFS]
	   [FILE]...

	   Display FILEs (or stdin) in a user specified format

		   -b		   1-byte octal display
		   -c		   1-byte character display
		   -d		   2-byte decimal display
		   -o		   2-byte octal display
		   -x		   2-byte hex display
		   -C		   hex+ASCII 16 bytes per line
		   -v		   Show all (no dup folding)
		   -e FORMAT_STR   Example: '16/1 "%02x|""\n"'
		   -f FORMAT_FILE
		   -n LENGTH	   Show only first LENGTH bytes
		   -s OFFSET	   Skip OFFSET bytes

       hostid
	   hostid

	   Print out a unique 32-bit identifier for the machine

       hostname
	   hostname [-sidf] [HOSTNAME | -F FILE]

	   Show or set hostname or DNS domain name

		   -s	   Short
		   -i	   Addresses for the hostname
		   -d	   DNS domain name
		   -f	   Fully qualified domain name
		   -F FILE Use FILE's content as hostname

       httpd
	   httpd  [-ifv[v]]  [-c  CONFFILE]  [-p [IP:]PORT] [-u USER[:GRP]] [-r
	   REALM] [-h HOME] or httpd -d/-e/-m STRING

	   Listen for incoming HTTP requests

		   -i		   Inetd mode
		   -f		   Run in foreground
		   -v[v]	   Verbose
		   -p [IP:]PORT	   Bind to IP:PORT (default *:80)
		   -u USER[:GRP]   Set uid/gid after binding to port
		   -r REALM	   Authentication Realm for Basic Authentication
		   -h HOME	   Home directory (default .)
		   -c FILE	   Configuration file (default {/etc,HOME}/httpd.conf)
		   -m STRING	   MD5 crypt STRING
		   -e STRING	   HTML encode STRING
		   -d STRING	   URL decode STRING

       hwclock
	   hwclock [-ul] [-f DEV] [-s|-w|--systz|--param-get  PARAM|--param-set
	   PARAM=VAL]

	   Show or set hardware clock (RTC)

		   -f DEV  Use this device (e.g. /dev/rtc2)
		   -u	   Assume RTC is kept in UTC
		   -l	   Assume RTC is kept in local time
			   (if neither is given, read from /etc/adjtime)
		   -s	   Set system time from RTC
		   -w	   Set RTC from system time
		   --systz Set in-kernel timezone, correct system time
			   if RTC is kept in local time
		   --param-get PARAM	   Get RTC parameter
		   --param-set PARAM=VAL   Set RTC parameter

       i2cdetect
	   i2cdetect -l | -F I2CBUS | [-ya] [-q|-r] I2CBUS [FIRST LAST]

	   Detect I2C chips

		   -l	   List installed buses
		   -F BUS# List functionalities on this bus
		   -y	   Disable interactive mode
		   -a	   Force scanning of non-regular addresses
		   -q	   Use smbus quick write commands for probing (default)
		   -r	   Use smbus read byte commands for probing
		   FIRST and LAST limit probing range

       i2cdump
	   i2cdump [-fy] [-r FIRST-LAST] BUS ADDR [MODE]

	   Examine I2C registers

		   I2CBUS  I2C bus number
		   ADDRESS 0x03-0x77
	   MODE is:

		   b	   Byte (default)
		   w	   Word
		   W	   Word on even register addresses
		   i	   I2C block
		   s	   SMBus block
		   c	   Consecutive byte
		   Append p for SMBus PEC

		   -f	   Force access
		   -y	   Disable interactive mode
		   -r	   Limit the number of registers being accessed

       i2cget
	   i2cget [-fy] BUS CHIP-ADDRESS [DATA-ADDRESS [MODE]]

	   Read from I2C/SMBus chip registers

		   I2CBUS  I2C bus number
		   ADDRESS 0x03-0x77
	   MODE is:

		   b	   Read byte data (default)
		   w	   Read word data
		   c	   Write byte/read byte
		   Append p for SMBus PEC

		   -f	   Force access
		   -y	   Disable interactive mode

       i2cset
	   i2cset  [-fy]  [-m  MASK]  BUS CHIP-ADDRESS DATA-ADDRESS [VALUE] ...
	   [MODE]

	   Set I2C registers

		   I2CBUS  I2C bus number
		   ADDRESS 0x03-0x77
	   MODE is:

		   c	   Byte, no value
		   b	   Byte data (default)
		   w	   Word data
		   i	   I2C block data
		   s	   SMBus block data
		   Append p for SMBus PEC

		   -f	   Force access
		   -y	   Disable interactive mode
		   -r	   Read back and compare the result
		   -m MASK Mask specifying which bits to write

       i2ctransfer
	   i2ctransfer	[-fay]	I2CBUS	{   rLENGTH[@ADDR]   |	 wLENGTH[@ADDR]
	   DATA...}...

	   Read/write I2C data in one transfer

		   -f	   Force access to busy addresses
		   -a	   Force access to non-regular addresses
		   -y	   Disable interactive mode

       id  id [-ugGnr] [USER]

	   Print information about USER or the current user

		   -u	   User ID
		   -g	   Group ID
		   -G	   Supplementary group IDs
		   -n	   Print names instead of numbers
		   -r	   Print real ID instead of effective ID

       ifconfig
	   ifconfig [-a] [IFACE] [ADDRESS]

	   Configure a network interface

		   [add ADDRESS[/PREFIXLEN]]
		   [del ADDRESS[/PREFIXLEN]]
		   [[-]broadcast [ADDRESS]] [[-]pointopoint [ADDRESS]]
		   [netmask ADDRESS] [dstaddr ADDRESS]
		   [outfill NN] [keepalive NN]
		   [hw ether|infiniband ADDRESS] [metric NN] [mtu NN]
		   [[-]trailers] [[-]arp] [[-]allmulti]
		   [multicast] [[-]promisc] [txqueuelen NN] [[-]dynamic]
		   [mem_start NN] [io_addr NN] [irq NN]
		   [up|down] ...

       ifdown
	   ifdown [-nmvf] [-i FILE] -a | IFACE...

		   -a	   Deconfigure all interfaces
		   -i FILE Use FILE instead of /etc/network/interfaces
		   -n	   Dry run
			   (note: doesn't disable mappings)
		   -m	   Don't run any mappings
		   -v	   Print out what would happen before doing it
		   -f	   Force

       ifup
	   ifup [-nmvf] [-i FILE] -a | IFACE...

		   -a	   Configure all interfaces
		   -i FILE Use FILE instead of /etc/network/interfaces
		   -n	   Dry run
			   (note: doesn't disable mappings)
		   -m	   Don't run any mappings
		   -v	   Print out what would happen before doing it
		   -f	   Force

       init
	   init

	   Init	 is  the first process started during boot. It never exits.  It
	   (re)spawns children according to /etc/inittab.  Signals:

	   HUP: reload /etc/inittab TSTP: stop respawning until CONT QUIT:  re-
	   exec	       another	      init	  USR1/TERM/USR2/INT:	    run
	   halt/reboot/poweroff/Ctrl-Alt-Del script

       insmod
	   insmod FILE [SYMBOL=VALUE]...

	   Load kernel module

       install
	   install [-cdDsp] [-o USER] [-g GRP] [-m MODE] [-t  DIR]  [SOURCE]...
	   DEST

	   Copy files and set attributes

		   -c	   Just copy (default)
		   -d	   Create directories
		   -D	   Create leading target directories
		   -s	   Strip symbol table
		   -p	   Preserve date
		   -o USER Set ownership
		   -g GRP  Set group ownership
		   -m MODE Set permissions
		   -t DIR  Install to DIR

       ionice
	   ionice [-c 1-3] [-n 0-7] [-t] { -p PID | PROG ARGS }

	   Change I/O priority and class

		   -c N	   Class. 1:realtime 2:best-effort 3:idle
		   -n N	   Priority
		   -t	   Ignore errors

       ip  ip [OPTIONS] address|route|link|tunnel|neigh|rule [ARGS]

	   OPTIONS := -f[amily] inet|inet6|link | -o[neline]

	   ip  addr  add|del  IFADDR  dev  IFACE  |  show|flush [dev IFACE] [to
	   PREFIX] ip route list|flush|add|del|change|append|replace|test ROUTE
	   ip  link  set  IFACE	 [up|down]  [arp  on|off]  [multicast	on|off]
		[promisc on|off] [mtu NUM] [name NAME] [qlen NUM] [address MAC]
		[master	 IFACE	|  nomaster]  [netns  PID]  [type TYPE ARGS] ip
	   tunnel add|change|del|show [NAME]	  [mode	 ipip|gre|sit]	[remote
	   ADDR]  [local  ADDR]	 [ttl TTL] ip neigh show|flush [to PREFIX] [dev
	   DEV] [nud STATE] ip rule [list] | add|del SELECTOR ACTION

       ipcalc
	   ipcalc [-bnmphs] ADDRESS[/PREFIX] [NETMASK]

	   Calculate and display network settings from IP address

		   -b	   Broadcast address
		   -n	   Network address
		   -m	   Default netmask for IP
		   -p	   Prefix for IP/NETMASK
		   -h	   Resolved host name
		   -s	   No error messages

       kill
	   kill [-l] [-SIG] PID...

	   Send a signal (default: TERM) to given PIDs

		   -l	   List all signal names and numbers

       killall
	   killall [-lq] [-SIG] PROCESS_NAME...

	   Send a signal (default: TERM) to given processes

		   -l	   List all signal names and numbers
		   -q	   Don't complain if no processes were killed

       klogd
	   klogd [-c N] [-n]

	   Log kernel messages to syslog

		   -c N	   Print to console messages more urgent than prio N (1-8)
		   -n	   Run in foreground

       last
	   last

	   Show listing of the last users that logged into the system

       less
	   less [-EFIMmNSRh~] [FILE]...

	   View FILE (or stdin) one screenful at a time

		   -E	   Quit once the end of a file is reached
		   -F	   Quit if entire file fits on first screen
		   -I	   Ignore case in all searches
		   -M,-m   Display status line with line numbers
			   and percentage through the file
		   -N	   Prefix line number to each line
		   -S	   Truncate long lines
		   -R	   Remove color escape codes in input
		   -~	   Suppress ~s displayed past EOF

       link
	   link FILE LINK

	   Create hard LINK to FILE

       ln  ln [-sfnbtv] [-S SUF] TARGET... LINK|DIR

	   Create a link LINK or DIR/TARGET to the specified TARGET(s)

		   -s	   Make symlinks instead of hardlinks
		   -f	   Remove existing destinations
		   -n	   Don't dereference symlinks - treat like normal file
		   -b	   Make a backup of the target (if exists) before link operation
		   -S SUF  Use suffix instead of ~ when making backup files
		   -T	   Treat LINK as a file, not DIR
		   -v	   Verbose

       loadfont
	   loadfont < font

	   Load a console font from stdin

       loadkmap
	   loadkmap < keymap

	   Load a binary keyboard translation table from stdin

       logger
	   logger [-s] [-t TAG] [-p PRIO] [MESSAGE]

	   Write MESSAGE (or stdin) to syslog

		   -s	   Log to stderr as well as the system log
		   -t TAG  Log using the specified tag (defaults to user name)
		   -p PRIO Priority (number or FACILITY.LEVEL pair)

       login
	   login [-p] [-h HOST] [[-f] USER]

	   Begin a new session on the system

		   -f	   Don't authenticate (user already authenticated)
		   -h HOST Host user came from (for network logins)
		   -p	   Preserve environment

	   $LOGIN_TIMEOUT      Seconds (default 60, 0 - disable)

       logname
	   logname

	   Print the name of the current user

       logread
	   logread [-fF]

	   Show messages in syslogd's circular buffer

		   -f	   Output data as log grows
		   -F	   Same as -f, but dump buffer first

       losetup
	   losetup [-rP] [-o OFS] {-f|LOOPDEV}	FILE:  associate  loop	devices
		losetup	 -c  LOOPDEV: reread file size	    losetup -d LOOPDEV:
	   disassociate	     losetup -a: show status	  losetup -f: show next
	   free loop device

		   -o OFS  Start OFS bytes into FILE
		   -P	   Scan for partitions
		   -r	   Read-only
		   -f	   Show/use next free loop device

       ls  ls [-1AaCxdLHRFplinshrSXvctu] [-w WIDTH] [FILE]...

	   List directory contents

		   -1	   One column output
		   -a	   Include names starting with .
		   -A	   Like -a, but exclude . and ..
		   -x	   List by lines
		   -d	   List directory names, not contents
		   -L	   Follow symlinks
		   -H	   Follow symlinks on command line
		   -R	   Recurse
		   -p	   Append / to directory names
		   -F	   Append indicator (one of */=@|) to names
		   -l	   Long format
		   -i	   List inode numbers
		   -n	   List numeric UIDs and GIDs instead of names
		   -s	   List allocated blocks
		   -lc	   List ctime
		   -lu	   List atime
		   --full-time	   List full date/time
		   -h	   Human readable sizes (1K 243M 2G)
		   --group-directories-first
		   -S	   Sort by size
		   -X	   Sort by extension
		   -v	   Sort by version
		   -t	   Sort by mtime
		   -tc	   Sort by ctime
		   -tu	   Sort by atime
		   -r	   Reverse sort order
		   -w N	   Format N columns wide
		   --color[={always,never,auto}]

       lsmod
	   lsmod

	   List loaded kernel modules

       lzcat
	   lzcat [FILE]...

	   Decompress to stdout

       lzma
	   lzma -d [-cfk] [FILE]...

	   Decompress FILEs (or stdin)

		   -d	   Decompress
		   -c	   Write to stdout
		   -f	   Force
		   -k	   Keep input files
		   -t	   Test integrity

       lzop
	   lzop [-cfUvd123456789CF] [FILE]...

		   -1..9   Compression level
		   -d	   Decompress
		   -c	   Write to stdout
		   -f	   Force
		   -U	   Delete input files
		   -v	   Verbose
		   -F	   Don't store or verify checksum
		   -C	   Also write checksum of compressed block

       md5sum
	   md5sum [-c[sw]] [FILE]...

	   Print or check MD5 checksums

		   -c	   Check sums against list in FILEs
		   -s	   Don't output anything, status code shows success
		   -w	   Warn about improperly formatted checksum lines

       mdev
	   mdev [-vS] { [-s] | [-df] }

		   -v	   Verbose
		   -S	   Log to syslog too
		   -s	   Scan /sys and populate /dev
		   -d	   Daemon, listen on netlink
		   -f	   Run in foreground

	   Bare mdev is a kernel hotplug  helper.  To  activate	 it:	   echo
	   /sbin/mdev >/proc/sys/kernel/hotplug

	   It  uses  /etc/mdev.conf  with  lines      [-][ENV=regex;]...DEVNAME
	   UID:GID PERM [>|=PATH]|[!] [@|$|*PROG] where DEVNAME is device  name
	   regex,  @major,minor[-minor2],  or  environment  variable  regex.  A
	   common use of the latter is to load modules for hotplugged devices:

		   $MODALIAS=.* 0:0 660 @modprobe "$MODALIAS"

	   If /dev/mdev.seq file exists, mdev will wait for its value to  match
	   $SEQNUM variable. This prevents plug/unplug races.  To activate this
	   feature, create empty /dev/mdev.seq at boot.

	   If /dev/mdev.log file exists, debug log will be appended to it.

       microcom
	   microcom [-d DELAY_MS] [-t TIMEOUT_MS ] [-s SPEED] [-X] TTY

	   Copy bytes from stdin to TTY and from TTY to stdout

		   -d DELAY	   Wait up to DELAY ms for TTY output before sending
				   every next byte to it
		   -t TIMEOUT	   Exit if both stdin and TTY are silent for TIMEOUT ms
		   -s SPEED	   Set serial line to SPEED
		   -X		   Disable special meaning of NUL and Ctrl-X from stdin

       mim mim [-f FILE] [SHELL_OPTIONS] [TARGET] ...

	   Run a script from a Makefile-like specification file

		   -f FILE	   Spec file (default Mimfile)

       mkdir
	   mkdir [-m MODE] [-p] DIRECTORY...

	   Create DIRECTORY

		   -m MODE Mode
		   -p	   No error if exists; make parent directories as needed

       mkdosfs
	   mkdosfs [-v] [-n LABEL] BLOCKDEV [KBYTES]

	   Make a FAT32 filesystem

		   -v	   Verbose
		   -n LBL  Volume label

       mke2fs
	   mke2fs  [-Fn]  [-b  BLK_SIZE]  [-i  INODE_RATIO] [-I INODE_SIZE] [-m
	   RESERVED_PERCENT] [-L LABEL] BLOCKDEV [KBYTES]

		   -b BLK_SIZE	   Block size, bytes
		   -F		   Force
		   -i RATIO	   Max number of files is filesystem_size / RATIO
		   -I BYTES	   Inode size (min 128)
		   -L LBL	   Volume label
		   -m PERCENT	   Percent of blocks to reserve for admin
		   -n		   Dry run

       mkfifo
	   mkfifo [-m MODE] NAME

	   Create named pipe

		   -m MODE Mode (default a=rw)

       mknod
	   mknod [-m MODE] NAME TYPE [MAJOR MINOR]

	   Create a special file (block, character, or pipe)

		   -m MODE Creation mode (default a=rw)
	   TYPE:
		   b	   Block device
		   c or u  Character device
		   p	   Named pipe (MAJOR MINOR must be omitted)

       mkpasswd
	   mkpasswd [-P FD] [-m TYPE] [-S SALT] [PASSWORD] [SALT]

	   Print crypt(3) hashed PASSWORD

		   -P N	   Read password from fd N
		   -m TYPE des,md5,sha256/512 (default )
		   -S SALT

       mkswap
	   mkswap [-L LBL] BLOCKDEV [KBYTES]

	   Prepare BLOCKDEV to be used as swap partition

		   -L LBL  Label

       mktemp
	   mktemp [-dt] [-p DIR] [TEMPLATE]

	   Create a temporary file with name based on TEMPLATE	and  print  its
	   name.   TEMPLATE  must  end	with  XXXXXX  (e.g. [/dir/]nameXXXXXX).
	   Without TEMPLATE, -t tmp.XXXXXX is assumed.

		   -d	   Make directory, not file
		   -q	   Fail silently on errors
		   -t	   Prepend base directory name to TEMPLATE
		   -p DIR  Use DIR as a base directory (implies -t)
		   -u	   Do not create anything; print a name

	   Base directory is: -p DIR, else $TMPDIR, else /tmp

       modinfo
	   modinfo [-adlpn0] [-F keyword] MODULE

		   -a		   Shortcut for '-F author'
		   -d		   Shortcut for '-F description'
		   -l		   Shortcut for '-F license'
		   -p		   Shortcut for '-F parm'
		   -F keyword	   Keyword to look for
		   -0		   NUL terminated output

       modprobe
	   modprobe [-alrqvsDb] MODULE [SYMBOL=VALUE]...

		   -a	   Load multiple MODULEs
		   -l	   List (MODULE is a pattern)
		   -r	   Remove MODULE (stacks) or do autoclean
		   -q	   Quiet
		   -v	   Verbose
		   -s	   Log to syslog
		   -D	   Show dependencies
		   -b	   Apply blacklist to module names too

       more
	   more [FILE]...

	   View FILE (or stdin) one screenful at a time

       mount
	   mount [OPTIONS] [-o OPT] DEVICE NODE

	   Mount a filesystem. Filesystem autodetection requires /proc.

		   -a		   Mount all filesystems in fstab
		   -f		   Dry run
		   -i		   Don't run mount helper
		   -r		   Read-only mount
		   -t FSTYPE[,...] Filesystem type(s)
		   -T FILE	   Read FILE instead of /etc/fstab
		   -O OPT	   Mount only filesystems with option OPT (-a only)
	   -o OPT:
		   loop		   Ignored (loop devices are autodetected)
		   [a]sync	   Writes are [a]synchronous
		   [no]atime	   Disable/enable updates to inode access times
		   [no]diratime	   Disable/enable atime updates to directories
		   [no]relatime	   Disable/enable atime updates relative to modification time
		   [no]dev	   (Dis)allow use of special device files
		   [no]exec	   (Dis)allow use of executable files
		   [no]suid	   (Dis)allow set-user-id-root programs
		   [r]shared	   Convert [recursively] to a shared subtree
		   [r]slave	   Convert [recursively] to a slave subtree
		   [r]private	   Convert [recursively] to a private subtree
		   [un]bindable	   Make mount point [un]able to be bind mounted
		   [r]bind	   Bind a file or directory [recursively] to another location
		   move		   Relocate an existing mount point
		   remount	   Remount a mounted filesystem, changing flags
		   ro		   Same as -r

	   There are filesystem-specific -o flags.

       mt  mt [-f DEVICE] OPCODE VALUE

	   Control magnetic tape drive operation

	   Opcodes:

	   bsf bsfm bsr bss datacompression drvbuffer eof eom  erase  fsf  fsfm
	   fsr	fss load lock mkpart nop offline ras1 ras2 ras3 reset retension
	   rewind rewoffline seek setblk setdensity setpart tell unload	 unlock
	   weof wset

       mv  mv  [-finT]	SOURCE	DEST  or:  mv [-fin] SOURCE... { -t DIRECTORY |
	   DIRECTORY }

	   Rename SOURCE to DEST, or move SOURCEs to DIRECTORY

		   -f	   Don't prompt before overwriting
		   -i	   Interactive, prompt before overwrite
		   -n	   Don't overwrite an existing file
		   -T	   Refuse to move if DEST is a directory
		   -t DIR  Move all SOURCEs into DIR

       nameif
	   nameif [-s] [-c FILE] [IFNAME HWADDR]...

	   Rename network interface while it in the  down  state.   The	 device
	   with address HWADDR is renamed to IFNAME.

		   -c FILE Configuration file (default: /etc/mactab)
		   -s	   Log to syslog

       nbd-client
	   nbd-client { [-b BLKSIZE] [-N NAME] [-t SEC] [-p] HOST [PORT] | -d }
	   BLOCKDEV

	   Connect to HOST and provide network block device on BLOCKDEV

       nc  nc [-iN] [-wN] [-l] [-p PORT] [-f FILE|IPADDR PORT] [-e PROG]

	   Open a pipe to IP:PORT or FILE

		   -l	   Listen mode, for inbound connects
			   (use -ll with -e for persistent server)
		   -p PORT Local port
		   -w SEC  Connect timeout
		   -i SEC  Delay interval for lines sent
		   -f FILE Use file (ala /dev/ttyS0) instead of network
		   -e PROG Run PROG after connect

       netstat
	   netstat [-ral] [-tuwx] [-en]

	   Display networking information

		   -r	   Routing table
		   -a	   All sockets
		   -l	   Listening sockets
			   Else: connected sockets
		   -t	   TCP sockets
		   -u	   UDP sockets
		   -w	   Raw sockets
		   -x	   Unix sockets
			   Else: all socket types
		   -e	   Other/more information
		   -n	   Don't resolve names

       nl  nl [OPTIONS] [FILE]...

	   Write FILEs to standard output with line numbers added

		   -b STYLE	   Which lines to number - a: all, t: nonempty, n: none
		   -i N		   Line number increment
		   -s STRING	   Use STRING as line number separator
		   -v N		   Start from N
		   -w N		   Width of line numbers

       nologin
	   nologin

	   Politely refuse a login

       nproc
	   nproc [--all] [--ignore=N]

	   Print number of available CPUs

		   --all	   Number of installed CPUs
		   --ignore=N	   Exclude N CPUs

       nsenter
	   nsenter [OPTIONS] [PROG ARGS]

		   -t PID	   Target process to get namespaces from
		   -m[FILE]	   Enter mount namespace
		   -u[FILE]	   Enter UTS namespace (hostname etc)
		   -i[FILE]	   Enter System V IPC namespace
		   -n[FILE]	   Enter network namespace
		   -p[FILE]	   Enter pid namespace
		   -U[FILE]	   Enter user namespace
		   -S UID	   Set uid in entered namespace
		   -G GID	   Set gid in entered namespace
		   --preserve-credentials  Don't touch uids or gids
		   -r[DIR]	   Set root directory
		   -w[DIR]	   Set working directory
		   -F		   Don't fork before exec'ing PROG

       nslookup
	   nslookup [-type=QUERY_TYPE] [-debug] HOST [DNS_SERVER]

	   Query DNS about HOST

	   QUERY_TYPE: soa,ns,a,aaaa,cname,mx,txt,ptr,srv,any

       nuke
	   nuke DIR...

	   Remove DIRs

       od  od  [-abcdfhilovxs]	[-t  TYPE]  [-A	 RADIX] [-N SIZE] [-j SKIP] [-S
	   MINSTR] [-w WIDTH] [FILE]...

	   Print FILEs (or stdin) unambiguously, as octal bytes by default

       openvt
	   openvt [-c N] [-sw] [PROG ARGS]

	   Start PROG on a new virtual terminal

		   -c N	   Use specified VT
		   -s	   Switch to the VT
		   -w	   Wait for PROG to exit

       partprobe
	   partprobe DEVICE...

	   Ask kernel to rescan partition table

       passwd
	   passwd [-a ALG] [-dlu] [USER]

	   Change USER's password (default: current user)

		   -a ALG  des,md5,sha256/512 (default )
		   -d	   Set password to ''
		   -l	   Lock (disable) account
		   -u	   Unlock (enable) account

       paste
	   paste [-d LIST] [-s] [FILE]...

	   Paste lines from each input file, separated with tab

		   -d LIST Use delimiters from LIST, not tab
		   -s	   Serial: one file at a time

       patch
	   patch [-RNE] [-p N] [-i DIFF] [ORIGFILE [PATCHFILE]]

		   -p N	   Strip N leading components from file names
		   -i DIFF Read DIFF instead of stdin
		   -R	   Reverse patch
		   -N	   Ignore already applied patches
		   -E	   Remove output files if they become empty
		   --dry-run	   Don't actually change files

       pidof
	   pidof [NAME]...

	   List PIDs of all processes with names that match NAMEs

       ping
	   ping [OPTIONS] HOST

	   Send ICMP ECHO_REQUESTs to HOST

		   -4,-6	   Force IP or IPv6 name resolution
		   -c CNT	   Send only CNT pings
		   -s SIZE	   Send SIZE data bytes in packets (default 56)
		   -i SECS	   Interval
		   -A		   Ping as soon as reply is received
		   -t TTL	   Set TTL
		   -I IFACE/IP	   Source interface or IP address
		   -W SEC	   Seconds to wait for the first response (default 10)
				   (after all -c CNT packets are sent)
		   -w SEC	   Seconds until ping exits (default:infinite)
				   (can exit earlier with -c CNT)
		   -q		   Quiet, only display output at start/finish
		   -p HEXBYTE	   Payload pattern

       ping6
	   ping6 [OPTIONS] HOST

	   Send ICMP ECHO_REQUESTs to HOST

		   -c CNT	   Send only CNT pings
		   -s SIZE	   Send SIZE data bytes in packets (default 56)
		   -i SECS	   Interval
		   -A		   Ping as soon as reply is received
		   -I IFACE/IP	   Source interface or IP address
		   -W SEC	   Seconds to wait for the first response (default 10)
				   (after all -c CNT packets are sent)
		   -w SEC	   Seconds until ping exits (default:infinite)
				   (can exit earlier with -c CNT)
		   -q		   Quiet, only display output at start/finish
		   -p HEXBYTE	   Payload pattern

       pivot_root
	   pivot_root NEW_ROOT PUT_OLD

	   Move the current root file system to PUT_OLD and make  NEW_ROOT  the
	   new root file system

       poweroff
	   poweroff [-d DELAY] [-nf]

	   Halt and shut off power

		   -d SEC  Delay interval
		   -n	   Do not sync
		   -f	   Force (don't go through init)

       printf
	   printf FORMAT [ARG]...

	   Format and print ARG(s) according to FORMAT (a-la C printf)

       ps  ps [-o COL1,COL2=HEADER] [-T]

	   Show list of processes

		   -o COL1,COL2=HEADER	   Select columns for display
		   -T			   Show threads

       pwd pwd

	   Print the full filename of the current working directory

       rdate
	   rdate [-s/-p] HOST

	   Set and print time from HOST using RFC 868

		   -s	   Only set system time
		   -p	   Only print time

       readlink
	   readlink [-fnv] FILE

	   Display the value of a symlink

		   -n	   Don't add newline
		   -f	   Canonicalize by following all symlinks
		   -v	   Verbose

       realpath
	   realpath FILE...

	   Print absolute pathnames of FILEs

       reboot
	   reboot [-d DELAY] [-nf]

	   Reboot the system

		   -d SEC  Delay interval
		   -n	   Do not sync
		   -f	   Force (don't go through init)

       renice
	   renice [-n] PRIORITY [[-p|g|u] ID...]...

	   Change scheduling priority of a running process

		   -n	   Add PRIORITY to current nice value
			   Without -n, nice value is set to PRIORITY
		   -p	   Process ids (default)
		   -g	   Process group ids
		   -u	   Process user names

       reset
	   reset

	   Reset terminal (ESC codes) and termios (signals, buffering, echo)

       resume
	   resume BLOCKDEV [OFFSET]

	   Restore system state from 'suspend-to-disk' data in BLOCKDEV

       rev rev [FILE]...

	   Reverse lines of FILE

       rm  rm [-irf] FILE...

	   Remove (unlink) FILEs

		   -i	   Always prompt before removing
		   -f	   Never prompt
		   -R,-r   Recurse

       rmdir
	   rmdir [-p] DIRECTORY...

	   Remove DIRECTORY if it is empty

		   -p	   Include parents
		   --ignore-fail-on-non-empty

       rmmod
	   rmmod [-wfa] [MODULE]...

	   Unload kernel modules

		   -w	   Wait until the module is no longer used
		   -f	   Force unload
		   -a	   Remove all unused modules (recursively)

       route
	   route  [-ne]	 [-A  inet[6]]	[{add|del} [-net|-host] TARGET [netmask
	   MASK]      [gw  GATEWAY]  [metric  N]  [mss	BYTES]	[window	 BYTES]
	   [reject] [IFACE]]

	   Show or edit kernel routing tables

		   -n	   Don't resolve names
		   -e	   Display other/more information
		   -A inet[6]	   Select address family

       rpm rpm -i PACKAGE.rpm; rpm -qp[ildc] PACKAGE.rpm

	   Manipulate RPM packages

	   Commands:

		   -i	   Install package
		   -qp	   Query package
		   -qpi	   Show information
		   -qpl	   List contents
		   -qpd	   List documents
		   -qpc	   List config files

       rpm2cpio
	   rpm2cpio PACKAGE.rpm

	   Output a cpio archive of the rpm file

       run-init
	   run-init  [-d  CAP,CAP...]  [-n]  [-c CONSOLE_DEV] NEW_ROOT NEW_INIT
	   [ARGS]

	   Free initramfs and switch to another root fs:

	   chroot to NEW_ROOT, delete all in /, move  NEW_ROOT	to  /,	execute
	   NEW_INIT. PID must be 1. NEW_ROOT must be a mountpoint.

		   -c DEV  Reopen stdio to DEV after switch
		   -d CAPS Drop capabilities
		   -n	   Dry run

       run-parts
	   run-parts	[-a    ARG]...	  [-u	UMASK]	 [--reverse]   [--test]
	   [--exit-on-error] DIRECTORY

	   Run a bunch of scripts in DIRECTORY

		   -a ARG	   Pass ARG as argument to scripts
		   -u UMASK	   Set UMASK before running scripts
		   --reverse	   Reverse execution order
		   --test	   Dry run
		   --exit-on-error Exit if a script exits with non-zero

       sed sed [-i[SFX]] [-nrE] [-f FILE]... [-e  CMD]...  [FILE]...   or:  sed
	   [-i[SFX]] [-nrE] CMD [FILE]...

		   -e CMD  Add CMD to sed commands to be executed
		   -f FILE Add FILE contents to sed commands to be executed
		   -i[SFX] Edit files in-place (otherwise write to stdout)
			   Optionally back files up, appending SFX
		   -n	   Suppress automatic printing of pattern space
		   -r,-E   Use extended regex syntax

	   If  no  -e  or  -f, the first non-option argument is the sed command
	   string.  Remaining arguments are input files (stdin if none).

       seq seq [-w] [-s SEP] [FIRST [INC]] LAST

	   Print numbers from FIRST to LAST,  in  steps	 of  INC.   FIRST,  INC
	   default to 1.

		   -w	   Pad with leading zeros
		   -s SEP  String separator

       setkeycodes
	   setkeycodes { SCANCODE KEYCODE }...

	   Modify  kernel's scancode-to-keycode map, allowing unusual keyboards
	   to generate usable keycodes.

	   SCANCODE is either xx or e0xx (hexadecimal), KEYCODE is decimal.

       setpriv
	   setpriv [OPTIONS] PROG ARGS

	   Run PROG with different privilege settings

	   -d,--dump	  Show		     current		   capabilities
	   --nnp,--no-new-privs	    Ignore    setuid/setgid   bits   and   file
	   capabilities	 --inh-caps   CAP,CAP  Set   inheritable   capabilities
	   --ambient-caps CAP,CAP  Set ambient capabilities

       setsid
	   setsid [-c] PROG ARGS

	   Run	PROG  in  a new session. PROG will have no controlling terminal
	   and will not be affected by keyboard signals (^C etc).

		   -c	   Set controlling terminal to stdin

       sh  sh [-il] [-|+Cabefmnuvx] [-|+o OPT]... [-c 'SCRIPT'	[ARG0  ARGS]  |
	   FILE ARGS | -s ARGS]

	   Unix shell interpreter

       sha1sum
	   sha1sum [-c[sw]] [FILE]...

	   Print or check SHA1 checksums

		   -c	   Check sums against list in FILEs
		   -s	   Don't output anything, status code shows success
		   -w	   Warn about improperly formatted checksum lines

       sha256sum
	   sha256sum [-c[sw]] [FILE]...

	   Print or check SHA256 checksums

		   -c	   Check sums against list in FILEs
		   -s	   Don't output anything, status code shows success
		   -w	   Warn about improperly formatted checksum lines

       sha3sum
	   sha3sum [-c[sw]] [-a BITS] [FILE]...

	   Print or check SHA3 checksums

		   -c	   Check sums against list in FILEs
		   -s	   Don't output anything, status code shows success
		   -w	   Warn about improperly formatted checksum lines
		   -a BITS 224 (default), 256, 384, 512

       sha512sum
	   sha512sum [-c[sw]] [FILE]...

	   Print or check SHA512 checksums

		   -c	   Check sums against list in FILEs
		   -s	   Don't output anything, status code shows success
		   -w	   Warn about improperly formatted checksum lines

       shred
	   shred [-fuz] [-n N] [-s SIZE] FILE...

	   Overwrite/delete FILEs

		   -f	   Chmod to ensure writability
		   -s SIZE Size to write
		   -n N	   Overwrite N times (default 3)
		   -z	   Final overwrite with zeros
		   -u	   Remove file

       shuf
	   shuf [-n NUM] [-o FILE] [-z] [FILE | -e [ARG...] | -i L-H]

	   Randomly permute lines

		   -n NUM  Output at most NUM lines
		   -o FILE Write to FILE, not standard output
		   -z	   NUL terminated output
		   -e	   Treat ARGs as lines
		   -i L-H  Treat numbers L-H as lines

       sleep
	   sleep [N]...

	   Pause  for  a  time equal to the total of the args given, where each
	   arg can have an optional suffix of (s)econds, (m)inutes, (h)ours, or
	   (d)ays

       sort
	   sort	       [-nrughMcszbdfiokt]	  [-o	      FILE]	    [-k
	   START[.OFS][OPTS][,END[.OFS][OPTS]] [-t CHAR] [FILE]...

	   Sort lines of text

		   -o FILE Output to FILE
		   -c	   Check whether input is sorted
		   -b	   Ignore leading blanks
		   -f	   Ignore case
		   -i	   Ignore unprintable characters
		   -d	   Dictionary order (blank or alphanumeric only)
		   -n	   Sort numbers
		   -g	   General numerical sort
		   -h	   Sort human readable numbers (2K 1G)
		   -M	   Sort month
		   -V	   Sort version
		   -t CHAR Field separator
		   -k N[,M] Sort by Nth field
		   -r	   Reverse sort order
		   -s	   Stable (don't sort ties alphabetically)
		   -u	   Suppress duplicate lines
		   -z	   NUL terminated input and output

       ssl_client
	   ssl_client [-e] -s FD [-r FD] [-n SNI]

       start-stop-daemon
	   start-stop-daemon -S|-K [OPTIONS] [-- ARGS]

	   Search for matching processes, and then -S: start a process unless a
	   matching process is found -K: stop all matching processes

	   Process matching:

		   -u USERNAME|UID Match only this user's processes
		   -n NAME	   Match processes with NAME
				   in comm field in /proc/PID/stat
		   -x EXECUTABLE   Match processes with this command
				   in /proc/PID/cmdline
		   -p FILE	   Match a process with PID from FILE
		   All specified conditions must match
	   -S only:
		   -x EXECUTABLE   Program to run
		   -a NAME	   Zeroth argument
		   -b		   Background
		   -O FILE	   Append stdout and stderr to FILE
		   -N N		   Change nice level
		   -c USER[:[GRP]] Change user/group
		   -d DIR	   Change to DIR
		   -m		   Write PID to pidfile specified by -p
	   -K only:
		   -s SIG	   Signal to send
		   -t		   Match only, exit with 0 if found
	   Other:

		   -o		   Exit with status 0 if nothing is done
		   -v		   Verbose
		   -q		   Quiet

       stat
	   stat [-ltf] [-c FMT] FILE...

	   Display file (default) or filesystem status

		   -c FMT  Use the specified format
		   -f	   Display filesystem status
		   -L	   Follow links
		   -t	   Terse display

	   FMT sequences for files:

	    %a	   Access rights in octal
	    %A	   Access rights in human readable form
	    %b	   Number of blocks allocated (see %B)
	    %B	   Size in bytes of each block reported by %b
	    %d	   Device number in decimal
	    %D	   Device number in hex
	    %f	   Raw mode in hex
	    %F	   File type
	    %g	   Group ID
	    %G	   Group name
	    %h	   Number of hard links
	    %i	   Inode number
	    %n	   File name
	    %N	   File name, with -> TARGET if symlink
	    %o	   I/O block size
	    %s	   Total size in bytes
	    %t	   Major device type in hex
	    %T	   Minor device type in hex
	    %u	   User ID
	    %U	   User name
	    %x	   Time of last access
	    %X	   Time of last access as seconds since Epoch
	    %y	   Time of last modification
	    %Y	   Time of last modification as seconds since Epoch
	    %z	   Time of last change
	    %Z	   Time of last change as seconds since Epoch

	   FMT sequences for file systems:

	    %a	   Free blocks available to non-superuser
	    %b	   Total data blocks
	    %c	   Total file nodes
	    %d	   Free file nodes
	    %f	   Free blocks
	    %i	   File System ID in hex
	    %l	   Maximum length of filenames
	    %n	   File name
	    %s	   Block size (for faster transfer)
	    %S	   Fundamental block size (for block counts)
	    %t	   Type in hex
	    %T	   Type in human readable form

       strings
	   strings [-fo] [-t o|d|x] [-n LEN] [FILE]...

	   Display printable strings in a binary file

		   -f		   Precede strings with filenames
		   -o		   Precede strings with octal offsets
		   -t o|d|x	   Precede strings with offsets in base 8/10/16
		   -n LEN	   At least LEN characters form a string (default 4)

       stty
	   stty [-a|g] [-F DEVICE] [SETTING]...

	   Without arguments, prints baud rate, line discipline, and deviations
	   from stty sane

		   -F DEVICE	   Open device instead of stdin
		   -a		   Print all current settings in human-readable form
		   -g		   Print in stty-readable form
		   [SETTING]	   See manpage

       su  su [-lmp] [-s SH] [-] [USER [FILE ARGS | -c 'CMD' [ARG0 ARGS]]]

	   Run shell under USER (by default, root)

		   -,-l	   Clear environment, go to home dir, run shell as login shell
		   -p,-m   Do not set new $HOME, $SHELL, $USER, $LOGNAME
		   -c CMD  Command to pass to 'sh -c'
		   -s SH   Shell to use instead of user's default

       sulogin
	   sulogin [-t N] [TTY]

	   Single user login

		   -p	   Start a login shell
		   -t SEC  Timeout

       svc svc [-udopchaitkx] SERVICE_DIR...

	   Control services monitored by runsv supervisor

		   -u	   If service is not running, start it; restart if it stops
		   -d	   If service is running, send TERM+CONT signals; do not restart it
		   -o	   Once: if service is not running, start it; do not restart it
		   -pchaitk Send STOP, CONT, HUP, ALRM, INT, TERM, KILL signal to service
		   -x	   Exit: runsv will exit as soon as the service is down

       svok
	   svok SERVICE_DIR

	   Check  whether  runsv  supervisor  is running.  Exit code is 0 if it
	   does, 100 if it does not, 111 (with error  message)	if  SERVICE_DIR
	   does not exist.

       swapoff
	   swapoff [-a] [DEVICE]

	   Stop swapping on DEVICE

		   -a	   Stop swapping on all swap devices

       swapon
	   swapon [-a] [-e] [-d[POL]] [DEVICE]

	   Start swapping on DEVICE

		   -a	   Start swapping on all swap devices
		   -d[POL] Discard blocks at swapon (POL=once),
			   as freed (POL=pages), or both (POL omitted)
		   -e	   Silently skip devices that do not exist

       switch_root
	   switch_root [-c CONSOLE_DEV] NEW_ROOT NEW_INIT [ARGS]

	   Free initramfs and switch to another root fs:

	   chroot  to  NEW_ROOT,  delete  all in /, move NEW_ROOT to /, execute
	   NEW_INIT. PID must be 1. NEW_ROOT must be a mountpoint.

		   -c DEV  Reopen stdio to DEV after switch

       sync
	   sync [-df] [FILE]...

	   Write all buffered blocks (in FILEs) to disk	     -d	  Avoid syncing
	   metadata	 -f   Sync filesystems underlying FILEs

       sysctl
	   sysctl [-enq] { -a | -p [FILE]... | [-w] [KEY[=VALUE]]... }

	   Show/set kernel parameters

		   -e	   Don't warn about unknown keys
		   -n	   Don't show key names
		   -q	   Quiet
		   -a	   Show all values
		   -p	   Set values from FILEs (default /etc/sysctl.conf)
		   -w	   Set values

       syslogd
	   syslogd [OPTIONS]

	   System logging utility

		   -n		   Run in foreground
		   -R HOST[:PORT]  Log to HOST:PORT (default PORT:514)
		   -L		   Log locally and via network (default is network only if -R)
		   -C[size_kb]	   Log to shared mem buffer (use logread to read it)
		   -O FILE	   Log to FILE (default: /var/log/messages, stdout if -)
		   -s SIZE	   Max size (KB) before rotation (default 200KB, 0=off)
		   -b N		   N rotated logs to keep (default 1, max 99, 0=purge)
		   -l N		   Log only messages more urgent than prio N (1-8)
		   -S		   Smaller output
		   -t		   Strip client-generated timestamps
		   -D		   Drop duplicates
		   -f FILE	   Use FILE as config (default:/etc/syslog.conf)

       tac tac [FILE]...

	   Concatenate FILEs and print them in reverse

       tail
	   tail [OPTIONS] [FILE]...

	   Print last 10 lines of FILEs (or stdin)  to.	  With	more  than  one
	   FILE, precede each with a filename header.

		   -c [+]N[bkm]	   Print last N bytes
		   -n N[bkm]	   Print last N lines
		   -n +N[bkm]	   Start on Nth line and print the rest
				   (b:*512 k:*1024 m:*1024^2)
		   -q		   Never print headers
		   -v		   Always print headers
		   -f		   Print data as file grows
		   -F		   Same as -f, but keep retrying
		   -s SECONDS	   Wait SECONDS between reads with -f

       tar tar c|x|t [-ZzJjahmvokO] [-f TARFILE] [-C DIR] [FILE]...

	   Create, extract, or list files from a tar file

		   c	   Create
		   x	   Extract
		   t	   List
		   -f FILE Name of TARFILE ('-' for stdin/out)
		   -C DIR  Change to DIR before operation
		   -v	   Verbose
		   -O	   Extract to stdout
		   -m	   Don't restore mtime
		   -o	   Don't restore user:group
		   -k	   Don't replace existing files
		   -Z	   (De)compress using compress
		   -z	   (De)compress using gzip
		   -J	   (De)compress using xz
		   -j	   (De)compress using bzip2
		   --lzma  (De)compress using lzma
		   -a	   (De)compress based on extension
		   -h	   Follow symlinks
		   --overwrite		   Replace existing files
		   --strip-components NUM  NUM of leading components to strip
		   --no-recursion	   Don't descend in directories
		   --numeric-owner	   Use numeric user:group
		   --no-same-permissions   Don't restore access permissions
		   --to-command COMMAND	   Pipe files to COMMAND

       taskset
	   taskset [-ap] [HEXMASK | -c LIST] { PID | PROG ARGS }

	   Set or get CPU affinity

		   -p	   Operate on PID
		   -a	   Operate on all threads
		   -c	   Affinity is a list, not mask

       tc  tc OBJECT CMD [dev STRING]

	   OBJECT: qdisc|class|filter CMD: add|del|change|replace|show

	   qdisc     [handle	 QHANDLE]     [root|ingress|parent     CLASSID]
		[[QDISC_KIND]	   [help|OPTIONS]]	     QDISC_KIND	     :=
	   [p|b]fifo|tbf|prio|red|etc.	qdisc show [dev STRING] [ingress] class
	   [classid    CLASSID]	   [root|parent	  CLASSID]	  [[QDISC_KIND]
	   [help|OPTIONS] ] class show [ dev  STRING  ]	 [root|parent  CLASSID]
	   filter  [pref  PRIO]	 [protocol  PROTO]	 [root|classid CLASSID]
	   [handle FILTERID]	  [[FILTER_TYPE]  [help|OPTIONS]]  filter  show
	   [dev STRING] [root|parent CLASSID]

       tee tee [-ai] [FILE]...

	   Copy stdin to each FILE, and also to stdout

		   -a	   Append to the given FILEs, don't overwrite
		   -i	   Ignore interrupt signals (SIGINT)

       telnet
	   telnet [-a] [-l USER] HOST [PORT]

	   Connect to telnet server

		   -a	   Automatic login with $USER variable
		   -l USER Automatic login as USER

       tftp
	   tftp [OPTIONS] HOST [PORT]

	   Transfer a file from/to tftp server

		   -l FILE Local FILE
		   -r FILE Remote FILE
		   -g	   Get file
		   -p	   Put file
		   -b SIZE Transfer blocks in bytes

       time
	   time [-vpa] [-o FILE] PROG ARGS

	   Run PROG, display resource usage when it exits

		   -v	   Verbose
		   -p	   POSIX output format
		   -f FMT  Custom format
		   -o FILE Write result to FILE
		   -a	   Append (else overwrite)

       timeout
	   timeout [-s SIG] [-k KILL_SECS] SECS PROG ARGS

	   Run PROG. Send SIG to it if it is not gone in SECS seconds.	Default
	   SIG: TERM.If it still exists in KILL_SECS seconds, send KILL.

       top top [-bH] [-n COUNT] [-d SECONDS]

	   Show	 a  view  of process activity in real time.  Read the status of
	   all processes from /proc each SECONDS and show a screenful of  them.
	   Keys:

		   N/M/P/T: sort by pid/mem/cpu/time
		   R: reverse sort
		   H: toggle threads
		   Q,^C: exit
	   Options:

		   -b	   Batch mode
		   -n N	   Exit after N iterations
		   -d SEC  Delay between updates
		   -H	   Show threads

       touch
	   touch [-cham] [-d DATE] [-t DATE] [-r FILE] FILE...

	   Update mtime of FILEs

		   -c	   Don't create files
		   -h	   Don't follow links
		   -a	   Change only atime
		   -m	   Change only mtime
		   -d DT   Date/time to use
		   -t DT   Date/time to use
		   -r FILE Use FILE's date/time

       tr  tr [-cds] STRING1 [STRING2]

	   Translate,  squeeze,	 or  delete  characters	 from stdin, writing to
	   stdout

		   -c	   Take complement of STRING1
		   -d	   Delete input characters coded STRING1
		   -s	   Squeeze multiple output characters of STRING2 into one character

       traceroute
	   traceroute [-46Flnrv] [-f 1ST_TTL] [-m MAXTTL] [-q PROBES] [-p PORT]
		[-t  TOS]  [-w	WAIT_SEC]  [-s	SRC_IP]	 [-i  IFACE]	    [-z
	   PAUSE_MSEC] HOST [BYTES]

	   Trace the route to HOST

		   -4,-6   Force IP or IPv6 name resolution
		   -F	   Set don't fragment bit
		   -l	   Display TTL value of the returned packet
		   -n	   Print numeric addresses
		   -r	   Bypass routing tables, send directly to HOST
		   -v	   Verbose
		   -f N	   First number of hops (default 1)
		   -m N	   Max number of hops
		   -q N	   Number of probes per hop (default 3)
		   -p N	   Base UDP port number used in probes
			   (default 33434)
		   -s IP   Source address
		   -i IFACE Source interface
		   -t N	   Type-of-service in probe packets (default 0)
		   -w SEC  Wait for a response (default 3)
		   -z MSEC Wait before each send

       traceroute6
	   traceroute6	[-nrv]	[-f  1ST_TTL] [-m MAXTTL] [-q PROBES] [-p PORT]
		[-t  TOS]  [-w	WAIT_SEC]  [-s	SRC_IP]	 [-i  IFACE]	    [-z
	   PAUSE_MSEC] HOST [BYTES]

	   Trace the route to HOST

		   -n	   Print numeric addresses
		   -r	   Bypass routing tables, send directly to HOST
		   -v	   Verbose
		   -f N	   First number of hops (default 1)
		   -m N	   Max number of hops
		   -q N	   Number of probes per hop (default 3)
		   -p N	   Base UDP port number used in probes
			   (default 33434)
		   -s IP   Source address
		   -i IFACE Source interface
		   -t N	   Type-of-service in probe packets (default 0)
		   -w SEC  Wait for a response (default 3)
		   -z MSEC Wait before each send

       truncate
	   truncate [-c] -s SIZE FILE...

	   Truncate FILEs to SIZE

		   -c	   Do not create files
		   -s SIZE

       ts  ts [-is] [STRFTIME]

	   Pipe stdin to stdout, add timestamp to each line

		   -s	   Time since start
		   -i	   Time since previous line

       tty tty [-s]

	   Print file name of stdin's terminal

		   -s	   Print nothing, only return exit status

       tunctl
	   tunctl [-f DEVICE] [-t NAME | -d NAME]

	   Create or delete TUN/TAP interfaces

		   -f DEV  TUN device (default /dev/net/tun)
		   -t NAME Create iface (default: tapN)
		   -d NAME Delete iface

       ubirename
	   ubirename UBI_DEVICE OLD_VOLNAME NEW_VOLNAME [OLD2 NEW2]...

	   Rename UBI volumes on UBI_DEVICE

       udhcpc
	   udhcpc  [-fbqRB]  [-a[MSEC]]	 [-t  N]  [-T SEC] [-A SEC|-n]	    [-i
	   IFACE] [-s PROG] [-p PIDFILE]      [-oC] [-r	 IP]  [-V  VENDOR]  [-F
	   NAME] [-x OPT:VAL]... [-O OPT]...

		   -i IFACE	   Interface to use (default eth0)
		   -s PROG	   Run PROG at DHCP events (default /etc/udhcpc/default.script)
		   -p FILE	   Create pidfile
		   -B		   Request broadcast replies
		   -t N		   Send up to N discover packets (default 3)
		   -T SEC	   Pause between packets (default 3)
		   -A SEC	   Wait if lease is not obtained (default 20)
		   -b		   Background if lease is not obtained
		   -n		   Exit if lease is not obtained
		   -q		   Exit after obtaining lease
		   -R		   Release IP on exit
		   -f		   Run in foreground
		   -S		   Log to syslog too
		   -a[MSEC]	   Validate offered address with ARP ping
		   -r IP	   Request this IP address
		   -o		   Don't request any options (unless -O is given)
		   -O OPT	   Request option OPT from server (cumulative)
		   -x OPT:VAL	   Include option OPT in sent packets (cumulative)
				   Examples of string, numeric, and hex byte opts:
				   -x hostname:bbox - option 12
				   -x lease:3600 - option 51 (lease time)
				   -x 0x3d:0100BEEFC0FFEE - option 61 (client id)
				   -x 14:'"dumpfile"' - option 14 (shell-quoted)
		   -F NAME	   Ask server to update DNS mapping for NAME
		   -V VENDOR	   Vendor identifier (default 'udhcp VERSION')
		   -C		   Don't send MAC as client identifier
	   Signals:

		   USR1	   Renew lease
		   USR2	   Release lease

       udhcpc6
	   udhcpc6  [-fbqR]  [-t  N]  [-T SEC] [-A SEC|-n] [-i IFACE] [-s PROG]
		[-p PIDFILE] [-ldo] [-r IPv6] [-x OPT:VAL]... [-O OPT]...

		   -i IFACE	   Interface to use (default eth0)
		   -p FILE	   Create pidfile
		   -s PROG	   Run PROG at DHCP events (default /etc/udhcpc/default6.script)
		   -B		   Request broadcast replies
		   -t N		   Send up to N discover packets
		   -T SEC	   Pause between packets (default 3)
		   -A SEC	   Wait if lease is not obtained (default 20)
		   -b		   Background if lease is not obtained
		   -n		   Exit if lease is not obtained
		   -q		   Exit after obtaining lease
		   -R		   Release IP on exit
		   -f		   Run in foreground
		   -S		   Log to syslog too
		   -l		   Send 'information request' instead of 'solicit'
				   (used for servers which do not assign IPv6 addresses)
		   -r IPv6	   Request this address ('no' to not request any IP)
		   -d		   Request prefix
		   -o		   Don't request any options (unless -O is given)
		   -O OPT	   Request option OPT from server (cumulative)
		   -x OPT:VAL	   Include option OPT in sent packets (cumulative)
				   Examples of string, numeric, and hex byte opts:
				   -x hostname:bbox - option 12
				   -x lease:3600 - option 51 (lease time)
				   -x 0x3d:0100BEEFC0FFEE - option 61 (client id)
				   -x 14:'"dumpfile"' - option 14 (shell-quoted)
	   Signals:

		   USR1	   Renew lease
		   USR2	   Release lease

       udhcpd
	   udhcpd [-fS] [-I ADDR] [-a MSEC] [CONFFILE]

	   DHCP server

		   -f	   Run in foreground
		   -S	   Log to syslog too
		   -I ADDR Local address
		   -a MSEC Timeout for ARP ping (default 2000)
	   Signals:

		   USR1	   Update lease file

       uevent
	   uevent [PROG ARGS]

	   uevent runs PROG for every netlink notification.  PROG's environment
	   contains data passed from the kernel.   Typical  usage  (daemon  for
	   dynamic device node creation):      # uevent mdev & mdev -s

       umount
	   umount [-rlfda] [-t FSTYPE] FILESYSTEM|DIRECTORY

	   Unmount filesystems

		   -a	   Unmount all filesystems
		   -r	   Remount devices read-only if mount is busy
		   -l	   Lazy umount (detach filesystem)
		   -f	   Force umount (i.e., unreachable NFS server)
		   -d	   Free loop device if it has been used
		   -t FSTYPE[,...] Unmount only these filesystem type(s)

       uname
	   uname [-amnrspvio]

	   Print system information

		   -a	   Print all
		   -m	   Machine (hardware) type
		   -n	   Hostname
		   -r	   Kernel release
		   -s	   Kernel name (default)
		   -p	   Processor type
		   -v	   Kernel version
		   -i	   Hardware platform
		   -o	   OS name

       uncompress
	   uncompress [-cf] [FILE]...

	   Decompress FILEs (or stdin)

		   -c	   Write to stdout
		   -f	   Overwrite

       unexpand
	   unexpand [-fa][-t N] [FILE]...

	   Convert spaces to tabs, writing to stdout

		   -a	   Convert all blanks
		   -f	   Convert only leading blanks
		   -t N	   Tabstops every N chars

       uniq
	   uniq [-cduiz] [-f,s,w N] [FILE [OUTFILE]]

	   Discard duplicate lines

		   -c	   Prefix lines by the number of occurrences
		   -d	   Only print duplicate lines
		   -u	   Only print unique lines
		   -i	   Ignore case
		   -z	   NUL terminated output
		   -f N	   Skip first N fields
		   -s N	   Skip first N chars (after any skipped fields)
		   -w N	   Compare N characters in line

       unix2dos
	   unix2dos [-ud] [FILE]

	   Convert  FILE  in-place  from  Unix	to DOS format.	When no file is
	   given, use stdin/stdout.

		   -u	   dos2unix
		   -d	   unix2dos

       unlink
	   unlink FILE

	   Delete FILE by calling unlink()

       unlzma
	   unlzma [-cfk] [FILE]...

	   Decompress FILEs (or stdin)

		   -c	   Write to stdout
		   -f	   Force
		   -k	   Keep input files
		   -t	   Test integrity

       unshare
	   unshare [OPTIONS] [PROG ARGS]

		   -m,--mount[=FILE]	   Unshare mount namespace
		   -u,--uts[=FILE]	   Unshare UTS namespace (hostname etc.)
		   -i,--ipc[=FILE]	   Unshare System V IPC namespace
		   -n,--net[=FILE]	   Unshare network namespace
		   -p,--pid[=FILE]	   Unshare PID namespace
		   -U,--user[=FILE]	   Unshare user namespace
		   -f			   Fork before execing PROG
		   -r			   Map current user to root (implies -U)
		   --mount-proc[=DIR]	   Mount /proc filesystem first (implies -m)
		   --propagation slave|shared|private|unchanged
					   Modify mount propagation in mount namespace
		   --setgroups allow|deny  Control the setgroups syscall in user namespaces

       unxz
	   unxz [-cfk] [FILE]...

	   Decompress FILEs (or stdin)

		   -c	   Write to stdout
		   -f	   Force
		   -k	   Keep input files
		   -t	   Test integrity

       unzip
	   unzip [-lnojpqK] FILE[.zip] [FILE]... [-x FILE]... [-d DIR]

	   Extract FILEs from ZIP archive

		   -l	   List contents (with -q for short form)
		   -n	   Never overwrite files (default: ask)
		   -o	   Overwrite
		   -j	   Do not restore paths
		   -p	   Write to stdout
		   -t	   Test
		   -q	   Quiet
		   -K	   Do not clear SUID bit
		   -x FILE Exclude FILEs
		   -d DIR  Extract into DIR

       uptime
	   uptime

	   Display the time since the last boot

       usleep
	   usleep N

	   Pause for N microseconds

       uudecode
	   uudecode [-o OUTFILE] [INFILE]

	   Uudecode a file Finds OUTFILE in uuencoded source unless -o is given

       uuencode
	   uuencode [-m] [FILE] STORED_FILENAME

	   Uuencode FILE (or stdin) to stdout

		   -m	   Use base64 encoding per RFC1521

       vconfig
	   vconfig COMMAND [OPTIONS]

	   Create and remove virtual ethernet devices

		   add IFACE VLAN_ID
		   rem VLAN_NAME
		   set_flag IFACE 0|1 VLAN_QOS
		   set_egress_map VLAN_NAME SKB_PRIO VLAN_QOS
		   set_ingress_map VLAN_NAME SKB_PRIO VLAN_QOS
		   set_name_type NAME_TYPE

       vi  vi [-c CMD] [-R] [-H] [FILE]...

	   Edit FILE

		   -c CMD  Initial command to run ($EXINIT and ~/.exrc also available)
		   -R	   Read-only
		   -H	   List available features

       w   w

	   Show who is logged on

       watch
	   watch [-n SEC] [-t] PROG ARGS

	   Run PROG periodically

		   -n SEC  Period (default 2)
		   -t	   Don't print header

       watchdog
	   watchdog [-t N[ms]] [-T N[ms]] [-F] DEV

	   Periodically write to watchdog device DEV

		   -T N	   Reboot after N seconds if not reset (default 60)
		   -t N	   Reset every N seconds (default 30)
		   -F	   Run in foreground

	   Use 500ms to specify period in milliseconds

       wc  wc [-cmlwL] [FILE]...

	   Count lines, words, and bytes for FILEs (or stdin)

		   -c	   Count bytes
		   -m	   Count characters
		   -l	   Count newlines
		   -w	   Count words
		   -L	   Print longest line length

       wget
	   wget	 [-cqS]	 [--spider]  [-O  FILE]	 [-o  LOGFILE]	[--header  STR]
		[--post-data	STR    |    --post-file	  FILE]	  [-Y	on/off]
		[--no-check-certificate] [-P DIR] [-U AGENT] [-T SEC] URL...

	   Retrieve files via HTTP or FTP

		   --spider	   Only check URL existence: $? is 0 if exists
		   --header STR	   Add STR (of form 'header: value') to headers
		   --post-data STR Send STR using POST method
		   --post-file FILE	   Send FILE using POST method
		   --no-check-certificate  Don't validate the server's certificate
		   -c		   Continue retrieval of aborted transfer
		   -q		   Quiet
		   -P DIR	   Save to DIR (default .)
		   -S		   Show server response
		   -T SEC	   Network read timeout is SEC seconds
		   -O FILE	   Save to FILE ('-' for stdout)
		   -o LOGFILE	   Log messages to FILE
		   -U STR	   Use STR for User-Agent header
		   -Y on/off	   Use proxy

       which
	   which [-a] COMMAND...

	   Locate COMMAND

		   -a	   Show all matches

       who who [-aH]

	   Show who is logged on

		   -a	   Show all
		   -H	   Print column headers

       whoami
	   whoami

	   Print the user name associated with the current effective user id

       xargs
	   xargs [OPTIONS] [PROG ARGS]

	   Run PROG on every item given by stdin

		   -0	   NUL terminated input
		   -a FILE Read from FILE instead of stdin
		   -o	   Reopen stdin as /dev/tty
		   -r	   Don't run command if input is empty
		   -t	   Print the command on stderr before execution
		   -p	   Ask user whether to run each command
		   -E STR,-e[STR]  STR stops input processing
		   -I STR  Replace STR within PROG ARGS with input line
		   -n N	   Pass no more than N args to PROG
		   -s N	   Pass command line of no more than N bytes
		   -P N	   Run up to N PROGs in parallel
		   -x	   Exit if size is exceeded

       xxd xxd [-pri] [-g N] [-c N] [-l LEN] [-s OFS] [-o OFS] [FILE]

	   Hex dump FILE (or stdin)

		   -g N		   Bytes per group
		   -c N		   Bytes per line
		   -p		   Show only hex bytes, assumes -c30
		   -i		   C include file style
		   -l LENGTH	   Show only first LENGTH bytes
		   -s OFFSET	   Skip OFFSET bytes
		   -o OFFSET	   Add OFFSET to displayed offset
		   -r		   Reverse (with -p, assumes no offsets in input)

       xz  xz -d [-cfk] [FILE]...

	   Decompress FILEs (or stdin)

		   -d	   Decompress
		   -c	   Write to stdout
		   -f	   Force
		   -k	   Keep input files
		   -t	   Test integrity

       xzcat
	   xzcat [FILE]...

	   Decompress to stdout

       yes yes [STRING]

	   Repeatedly print a line with STRING, or 'y'

       zcat
	   zcat [FILE]...

	   Decompress to stdout

LIBC NSS
       GNU Libc (glibc) uses the Name Service Switch  (NSS)  to	 configure  the
       behavior	 of  the  C library for the local environment, and to configure
       how it reads system data, such as passwords and group information.  This
       is implemented using an /etc/nsswitch.conf configuration file, and using
       one or more of the /lib/libnss_*	 libraries.   BusyBox  tries  to  avoid
       using  any  libc calls that make use of NSS.  Some applets however, such
       as login and su, will use libc functions that require NSS.

       If you enable CONFIG_USE_BB_PWD_GRP, BusyBox will use internal functions
       to directly access the /etc/passwd, /etc/group,	and  /etc/shadow  files
       without	using  NSS.   This may allow you to run your system without the
       need for installing any of the NSS configuration files and libraries.

       When used with glibc, the BusyBox 'networking'  applets	will  similarly
       require	that  you  install  at	least  some  of the glibc NSS stuff (in
       particular,  /etc/nsswitch.conf,	 /lib/libnss_dns*,  /lib/libnss_files*,
       and /lib/libresolv*).

       Shameless  Plug:	 As  an	 alternative, one could use a C library such as
       uClibc.	In addition to making your system significantly smaller, uClibc
       does not require the use of any NSS support files or libraries.

MAINTAINER
       Denis Vlasenko <vda.linux@googlemail.com>

AUTHORS
       The following people have contributed code to BusyBox whether they  know
       it  or  not.   If  you have written code included in BusyBox, you should
       probably be listed here so you can obtain your bit of eternal glory.  If
       you should be listed here, or the description  of  what	you  have  done
       needs more detail, or is incorrect, please send in an update.

       Emanuele Aina <emanuele.aina@tiscali.it>

	   run-parts

       Erik Andersen <andersen@codepoet.org>

	   Tons of new stuff, major rewrite of most of the
	   core apps, tons of new apps as noted in header files.
	   Lots of tedious effort writing these boring docs that
	   nobody is going to actually read.

       Laurence Anderson <l.d.anderson@warwick.ac.uk>

	   rpm2cpio, unzip, get_header_cpio, read_gz interface, rpm

       Jeff Angielski <jeff@theptrgroup.com>

	   ftpput, ftpget

       Edward Betts <edward@debian.org>

	   expr, hostid, logname, whoami

       John Beppu <beppu@codepoet.org>

	   du, nslookup, sort

       Brian Candler <B.Candler@pobox.com>

	   tiny-ls(ls)

       Randolph Chung <tausq@debian.org>

	   fbset, ping, hostname

       Dave Cinege <dcinege@psychosis.com>

	   more(v2), makedevs, dutmp, modularization, auto links file,
	   various fixes, Linux Router Project maintenance

       Jordan Crouse <jordan@cosmicpenguin.net>

	   ipcalc

       Magnus Damm <damm@opensource.se>

	   tftp client insmod powerpc support

       Larry Doolittle <ldoolitt@recycle.lbl.gov>

	   pristine source directory compilation, lots of patches and fixes.

       Glenn Engel <glenne@engel.org>

	   httpd

       Gennady Feldman <gfeldman@gena01.com>

	   Sysklogd (single threaded syslogd, IPC Circular buffer support,
	   logread), various fixes.

       Karl M. Hegbloom <karlheg@debian.org>

	   cp_mv.c, the test suite, various fixes to utility.c, &c.

       Daniel Jacobowitz <dan@debian.org>

	   mktemp.c

       Matt Kraai <kraai@alumni.cmu.edu>

	   documentation, bugfixes, test suite

       Stephan Linz <linz@li-pro.net>

	   ipcalc, Red Hat equivalence

       John Lombardo <john@deltanet.com>

	   tr

       Glenn McGrath <bug1@iinet.net.au>

	   Common unarchiving code and unarchiving applets, ifupdown, ftpgetput,
	   nameif, sed, patch, fold, install, uudecode.
	   Various bugfixes, review and apply numerous patches.

       Manuel Novoa III <mjn3@codepoet.org>

	   cat, head, mkfifo, mknod, rmdir, sleep, tee, tty, uniq, usleep, wc, yes,
	   mesg, vconfig, make_directory, parse_mode, dirname, mode_string,
	   get_last_path_component, simplify_path, and a number trivial libbb routines

	   also bug fixes, partial rewrites, and size optimizations in
	   ash, basename, cal, cmp, cp, df, du, echo, env, ln, logname, md5sum, mkdir,
	   mv, realpath, rm, sort, tail, touch, uname, watch, arith, human_readable,
	   interface, dutmp, ifconfig, route

       Vladimir Oleynik <dzo@simtreas.ru>

	   cmdedit; xargs(current), httpd(current);
	   ports: ash, crond, fdisk, inetd, stty, traceroute, top;
	   locale, various fixes
	   and irreconcilable critic of everything not perfect.

       Bruce Perens <bruce@pixar.com>

	   Original author of BusyBox in 1995, 1996. Some of his code can
	   still be found hiding here and there...

       Tim Riker <Tim@Rikers.org>

	   bug fixes, member of fan club

       Kent Robotti <robotti@metconnect.com>

	   reset, tons and tons of bug reports and patches.

       Chip Rosenthal <chip@unicom.com>, <crosenth@covad.com>

	   wget - Contributed by permission of Covad Communications

       Pavel Roskin <proski@gnu.org>

	   Lots of bugs fixes and patches.

       Gyepi Sam <gyepi@praxis-sw.com>

	   Remote logging feature for syslogd

       Linus Torvalds <torvalds@transmeta.com>

	   mkswap, fsck.minix, mkfs.minix

       Mark Whitley <markw@codepoet.org>

	   grep, sed, cut, xargs(previous),
	   style-guide, new-applet-HOWTO, bug fixes, etc.

       Charles P. Wright <cpwright@villagenet.com>

	   gzip, mini-netcat(nc)

       Enrique Zanardi <ezanardi@ull.es>

	   tarcat (since removed), loadkmap, various fixes, Debian maintenance

       Tito Ragusa <farmatito@tiscali.it>

	   devfsd and size optimizations in strings, openvt and deallocvt.

       Paul Fox <pgf@foxharp.boston.ma.us>

	   vi editing mode for ash, various other patches/fixes

       Roberto A. Foglietta <me@roberto.foglietta.name>

	   port: dnsd

       Bernhard Reutner-Fischer <rep.dot.nop@gmail.com>

	   misc

       Mike Frysinger <vapier@gentoo.org>

	   initial e2fsprogs, printenv, setarch, sum, misc

       Jie Zhang <jie.zhang@analog.com>

	   fixed two bugs in msh and hush (exitcode of killed processes)

version 1.37.0			   2026-07-12			     BUSYBOX(1)